Panasonic PT-DZ16KD, PT-DZ16KE, PT-DZ16KU 149

Chapter 5 Maintenance — Maintenance/replacement

ii)Slide the lamp unit cover as shown by the arrow to fit it in the projector.

ff Attach the lamp unit cover so that the connector on the lamp unit cover is inserted to the fan power connector securely.

iii)Use a Phillips screwdriver to firmly tighten the lamp unit cover fixing screw (x1). ff Make sure to attach the lamp unit cover securely.

ENGLISH - 149

Contents

Operating Instructions DLP™ Projector Commercial Use Read this first CAUTION (North/Middle/South America and Taiwan) WARNING (USA and Canada) NOTIFICATION (Canada) For USA-CaliforniaOnly FCC NOTICE (USA) Product information (for Turkey only) IMPORTANT: THE MOULDED PLUG (U.K. only) rr POWER rr ON USE/INSTALLATION Page rr ACCESSORIES CAUTION: rr MAINTENANCE To remove the battery Remote Control Battery 1. Press the guide and lift the cover 2. Remove the batteries rrManuseio de baterias usadas BRASIL rrRemoção das baterias 1. Pressione a guia e levante a tampa 2. Remova as baterias rrTrademarks rIllustrations in this manual rReference pages rrTerm 1.Set up the projector. (xpage 35) 2.Attach the projection lens (optional) (xpage 41) 3.Connect with external devices. (xpage 43) 4.Connect the power cord. (xpage 47) Contents Page Maintenance Appendix Chapter 1 Preparation Precautions for use Cautions when transporting Cautions when installing rrDo not install and use the projector in portrait setting rrCautions when setting up the projector Security Art-Net Disposal Cautions on use rrDo not touch the surface of the projection lens with your bare hands rrDLP chips rrLamp rComputer and external device connections Accessories Optional accessories Start-updisplay Focus adjustment Initial setting (display language) Initial setting (installation setting 1) Initial setting (installation setting 2) Initial setting (screen setting) About your projector Remote control Page Projector body rrControl panel rrConnecting terminals Using the remote control Inserting and removing the batteries Setting the remote control ID numbers Connecting the remote control to the projector with a cable Chapter 2 Getting Started Setting up Installation mode Parts for ceiling mount (optional) Projected image and throw distance [GEOMETRY] projection range Projection distance of each projection lens rrWhen the screen aspect ratio is 16:9 rrWhen the screen aspect ratio is 4:3 Adjusting adjustable feet Attaching/removing the projection lens (optional) Attaching the projection lens Removing the projection lens Page Connecting Before connecting Connecting example: AV equipment Connecting example: Computers Chapter 3 Basic Operations Switching on/off the projector Connecting the power cord Power indicator Switching on the projector Making adjustments and selections Switching off the projector Projecting Selecting the input signal Adjusting the focus, zoom, and shift Moving the lens to the home position Adjustment range by the lens position shift (optical shift) Adjusting the lens mounter when the focus is unbalanced rrRelationship between the adjustment location and adjustment screws Operating with the remote control Using the shutter function Using the on-screendisplay function Switching the input signal Using the Status function Using the Automatic setup function Using the Function button Displaying the internal test pattern Changing the picture aspect ratio Settings Menu navigation Navigating through the menu Main menu Sub-menu [DISPLAY LANGUAGE] [DISPLAY OPTION] [PROJECTOR SETUP] [P IN P] [TEST PATTERN] [SIGNAL LIST] [SECURITY] [NETWORK] [PICTURE] menu [PICTURE MODE] [CONTRAST] [BRIGHTNESS] [COLOR] [TINT] [COLOR TEMPERATURE] Adjusting desired white balance Adjusting desired white balance based on existing color temperature settings [GAMMA] [SYSTEM DAYLIGHT VIEW] [SHARPNESS] [NOISE REDUCTION] [DYNAMIC IRIS] [SYSTEM SELECTOR] sRGB-compliantvideo [POSITION] menu [SHIFT] [ASPECT] [ZOOM] [CLOCK PHASE] [GEOMETRY] Setting [KEYSTONE] or [CURVED] Setting [CORNER CORRECTION] [ADVANCED MENU] menu [DIGITAL CINEMA REALITY] [BLANKING] [INPUT RESOLUTION] [CLAMP POSITION] [EDGE BLENDING] [FRAME RESPONSE] [RASTER POSITION] Page [DISPLAY LANGUAGE] menu Changing the display language [DISPLAY OPTION] menu [COLOR MATCHING] [LARGE SCREEN CORRECTION] [SCREEN SETTING] [AUTO SIGNAL] [AUTO SETUP] [RGB IN] [DVI-DIN] [HDMI IN] [SDI IN] Setting [SIGNAL LEVEL] Setting [BIT DEPTH] Setting [3G-SDIMAPPING] [ON-SCREENDISPLAY] [BACK COLOR] [STARTUP LOGO] [UNIFORMITY] [SHUTTER SETTING] [FREEZE] [WAVEFORM MONITOR] [CUT OFF] [PROJECTOR SETUP] menu [PROJECTOR ID] [PROJECTION METHOD] [COOLING CONDITION] [HIGH ALTITUDE MODE] [LAMP SELECT] [LAMP RELAY] [BRIGHTNESS CONTROL] Page Displaying [BRIGHTNESS CONTROL STATUS] [BRIGHTNESS CONTROL STATUS] screen display example rrError details [STANDBY MODE] [SCHEDULE] [STARTUP INPUT SELECT] [RS-232C] Setting the communication condition of the <SERIAL OUT> terminal Setting the response [STATUS] [NO SIGNAL SHUT-OFF] [REMOTE2 MODE] [FUNCTION BUTTON] [DATE AND TIME] [LENS CALIBRATION] [LENS MEMORY] [SAVE ALL USER DATA] [LOAD ALL USER DATA] [INITIALIZE] [SERVICE PASSWORD] [P IN P] menu Using P IN P function Page [TEST PATTERN] menu [TEST PATTERN] [SIGNAL LIST] menu Registering new signals Renaming the registered signal Deleting the registered signal Protecting the registered signal Expanding signal lock-inrange Sub memory [SECURITY] menu [SECURITY PASSWORD] [SECURITY PASSWORD CHANGE] [DISPLAY SETTING] [TEXT CHANGE] [CONTROL DEVICE SETUP] [CONTROL DEVICE PASSWORD CHANGE] Page [NETWORK] menu [NETWORK SETUP] [NETWORK CONTROL] [NETWORK STATUS] [Art-NetSETUP] Network connection Accessing from the web browser Descriptions of items [Projector status] page Error information page rr[FAILED] items rr[WARNING] items [Network status] page [Access error log] page [Access log] page [Basic control] page [Detail control] page [Network config] page [Adjust clock] page [Ping test] page [E-mailset up] page Page [Authentication set up] page Contents of E-mailsent Page [Change password] page Page Chapter 5 Maintenance Lamp/temperature/filter indicators When an indicator lights up Temperature indicator <TEMP Filter indicator <FILTER Maintenance/replacement Before performing maintenance/replacement Maintenance Page Replacing the unit Page Page Page Page Troubleshooting Page Self-diagnosisdisplay Page Page Appendix Technical information PJLink protocol Using Art-Netfunction Control commands via LAN rrTransmitted data rrReceived data rrError response When web control administrator rights password is not set (Non-protectmode) Page <SERIAL IN>/<SERIAL OUT> terminal Communication conditions (Factory default) Basic format Basic format (has subcommands) When multiple projectors are controlled Cable specification Control command rrProjector control command <REMOTE 2 IN> terminal Two-windowdisplay combination list Control device password List of compatible signals Page Specifications rrApplicable scanning frequency rrTerminal Dimensions Precautions for attaching the ceiling mount bracket Index Environment care information for users in China Panasonic System Communications Company of North America Panasonic Canada Inc