precautions on use
IMPORTANT NOTE
•Handle the liquid crystal display (LCD) with care:-The LCD is a very delicate display device: Do not press its surface with excessive force, hit it or prick it with a sharp object.
-If you push the LCD surface, unevenness in display may occur.
If unevenness does not disappear, turn the camcorder off, wait for a few moments, and then turn it on again.
-Do not place the camcorder with the open LCD screen down.-Close the LCD monitor when not using the camcorder•Liquid crystal display:-The LCD screen is a product of high precision technology. Out of the total pixels (approx. 112,000 pixels of an LCD monitor ), 0.01% or less pixels may be out (black dots) or may remain lit as colored dots (red, blue, and green). This shows the limitations of the current technology, and does not indicate a fault that will interfere with recording.
-The LCD screen will be slightly dimmer than usual when the camcorder is at low temperature, as in cold areas, or right after the power is turned on. Normal brightness will be restored when the temperature inside the camcorder rises. Note that the foregoing phenomena have no effect on the image in a storage media, so there is no cause for concern.
•Hold the memory camcorder correctly:-Do not hold the memory camcorder by the LCD monitor when lifting it: the LCD monitor could detach and the memory camcorder may fall.
•Do not subject the memory camcorder to impact:-This memory camcorder is a precision machine. Take great care that you do not strike it against a hard object or let it fall.
-Do not use the memory camcorder on a tripod in a place where it is subject to severe vibrations or impact.
•No sand or dust!-Fine sand or dust entering the memory camcorder or AC power adaptor could cause malfunctions or defects.
•No water or oil!-Water or oil entering the memory camcorder or AC power adaptor could cause electric shock, malfunctions or defects.
•Heat on surface of product:-The surface of the memory camcorder will be slightly warm when using, but this does not indicate a fault.
vi_English使用须知
重要注意事项
•细心处理液晶显示器 (LCD)：-LCD 是非常精密的显示设备：切勿用力压其表面，或使用 尖锐的物体击打或刺戳。-如果您按压 LCD 表面，可能会在显示时出现不平现象。如果不平现象不消失，请关闭摄像机，等待片刻后再次打开。-切勿使打开的 LCD 屏幕向下放置摄像机。-在不使用摄像机时关闭 LCD 显示器•液晶显示：-LCD 屏幕是采用高精密技术制造的产品。 在总像素（LCD 显示器的大约 112,000 像素）中，0.01% 或更少 的像素可能会损失（黑点），或可能以彩色（红、蓝和绿 色）的点亮起。 这表明了当前技术的局限性，但不表示 是影响录制的故障。
-当摄像机在温度较低的环境（如在寒冷地区）时，LCD 屏 幕会比正常时稍暗，或在打开电源后显示正常。当摄像机内部的温度上升时，会恢复到原来的亮度。 注意，上述现象对储存媒体中的图像没有什么影响， 因此无需顾虑。•正确把持数码摄像机：-不要握住数码摄像机的 LCD 显示器来提起它：LCD 显示 器可能会拆离，从而导致数码摄像机跌落。•切勿撞击数码摄像机：-本数码摄像机是精密机器。 要特别小心，不要让其撞击 硬物或摔落。-切勿在严重振动或撞击的地方将数码摄像机放在三角架上 使用。•要避免沙尘！-细沙或灰尘进入数码摄像机或交流电源适配器会引起故障。•要避免水或油！-水或油进入数码摄像机或交流电源适配器会引起触电或故障。•产品表面变热：-在使用时，数码摄像机表面会轻微变热，但这并不表示有 故障。