Registering through OpenLCR’s Web site | Sharp UX-465L instruction

4 Follow the instructions you hear.

Note: If you are on a pulse dial line, press the * key before pressing the number keys to respond.

(This makes your fax temporarily issue tone signals when you press the number keys.)

•When registration is completed, your fax machine will receive the rate data from OpenLCR. This will last one or two minutes. When downloading is completed, the display will briefly show DOWNLOAD OK!! and then revert to the date and time.

•OpenLCR will also program the date and time and your fax number in your fax machine.

Registering through

OpenLCR’s Web site

You can also register at OpenLCR’s Web site, www.OpenLCR.com. After registering you will need to receive the rate data manually (service is not activated until your fax receives the rate data). See Downloading (receiving) the rate data manually on the following page.

If you move, you must re-register!

Setting Up and Using OpenLCR

	The rate data that you receive is based
	on the address you provide when
	registering with OpenLCR. If you	Setting2.Up
	move, the rate data will not be correct		OpenLCR
	for your new location. In this case,		OpenLCR
	for your new location. In this case,
	repeat the registration procedure to
	give OpenLCR your new address.

Note: If you wish to connect more than one OpenLCR-enabled device to the same line, please call OpenLCR at 970-206-1207. If you replace an old OpenLCR-enabled device with a new one, you must re-register with OpenLCR to use the new device.

Note: OpenLCR cannot be used if your fax machine is connected to a Private Branch Exchange (PBX).

Downloading (receiving) the rate data manually

Your fax machine will automatically call OpenLCR and download updated rate data about once every three months. Normally you will not need to download the rate data manually.

♦If you register through OpenLCR’s Web site, you must manually download the rate data to activate service.

♦If the fax machine is unplugged or some other interruption occurs in the power, you will need to manually download the rate data.

Press these keys to call OpenLCR and initiate downloading:

2

OpenLCR

29

Image 31

Sharp UX-465L operation manual Registering through OpenLCR’s Web site, Downloading receiving the rate data manually

Contents

UX-465L For Your Records Introduction Halftone grayscale Power requirementsOperating temperature Power consumption Dimensions Important safety informationWeight Page Table of Contents Receiving Documents Look at the Operation Panel Speaker key Panel releaseNumber keys HOLD/SEARCH key About condensation InstallationUnpacking Checklist Points to keep in mind when setting up Connecting the power cord Connecting the HandsetConnections Connecting the telephone line cord Extension phone optional Attaching the tray extension and document support Loading the Imaging Film Do not Discard the Four Green Gears Click Sharp UX-3CR Imaging Film When to replace the imaging film Loading Printing Paper Letter Legal Installation1 # key Entering Your Name and Fax NumberKey Function key Stop key Start Example Do not set the date and time if you are using OpenLCR Setting the Date and TimeKey Stop key Daylight Saving Time Reception Mode key Setting the Reception ModeSetting the reception mode Press the Reception Mode key Down key UP key Volume AdjustmentSpeaker Handset Ringer Setting Up and Using OpenLCR Registering by phone Registering by fax Downloading receiving the rate data manually Registering through OpenLCR’s Web site Fax transmission test Using OpenLCR Meaning Mark Temporarily turning off OpenLCR To stop using OpenLCR What to do if E appears in the display Changing your user profile What to do if you cannot connect to OpenLCR Selecting a long or short call Changing the Short Time and Long Time settings Short Time Recording an Outgoing Message Using the Answering Machine Recording an Outgoing Message To listen to the outgoing message Activating the answering machine Operating the Answering MachineListening to received messages Erasing received messages Using the REC/MEMO key Press Date and time of ICMs Setting ICM time Optional Answering Machine SettingsFax reception on TAD failure Calling Party Control detection OGM only mode Programming the transfer number Transfer Function Turning the Transfer function on and off Recording the transfer message Programming the override code Override RingingOverriding the answering machine Override Ringing Remote code number Remote OperationsToll Saver Retrieving your messages Answering Machine Other remote operations Changing the fax reception modeComments Turning the Transfer function on or off Recording a new outgoing messageChanging the transfer telephone number Recording a Memo Recording a new transfer message Other restrictions Size and weightSending Documents Transmittable Documents Loading the Document Removing a document from the feeder Resolution settings Adjusting the Resolution and ContrastContrast settings Sending4 Documents Changing the default resolution Sending a Fax by Normal Dialing Using the Redial key Rapid Keys Sending a Fax by Automatic Dialing Enter a two-digit Speed Dial Storing fax and telephone numbers for Automatic Dialing Clearing auto-dial numbers Chain Dialing for area and access codes Making changes Speed Dialing Rapid Key Dialing Searching for an auto-dial number Direct Keypad Dialing Press the HOLD/SEARCH key and then the 1 key Recall Interval for automatic redialing Automatic redialingRecall times for automatic dialing Error Correction Mode Receiving Documents Using FAX Mode Changing the number of rings Answering with the fax’s handset Using TEL Mode Changing the number for remote fax activation Answering with an extension phone Turning off detection of the Tel/Fax Remote Number Fax Signal Receive Reception Ratio 1 Print Receiving Documents Substitute Reception to Memory START/MEMORY key twice Making CopiesSTART/MEMORY key and go to Copy Ratio Copy Cut-off Making Telephone Calls Redial Chain DialingHold Special Functions Caller ID Requires Subscription to Service Display messages How Caller ID operatesViewing the Caller ID list Priority Call To delete calls from the Caller ID list Blocking voice calls Setting Distinctive Ring Requires Subscription to Service Set the reception mode to FAX Broadcasting Cover Sheet Urgent Confidential PLS. Distribute Selecting a header message optional Batch Page Numbering Entering Anti Junk numbers Blocking Reception of Unwanted Faxes Press the START/MEMORY key Sending Documents From Memory If the memory becomes full Requesting transmission Polling Requesting a Fax Transmission Polling security Being polled polling standby Press these keys Storing and clearing fax Numbers for polling4 permission Setting a timer operation Timer Operations100 101 To cancel a timer operation Activity Report Printing Lists102 Explanation of headings 103 Telephone Number List Timer ListPasscode List Option Setting List Transaction Report Print Setup List105 Print head Maintenance106 107 Scanning glass and rollers Housing108 Problem Solution TroubleshootingProblems and Solutions Line error 110 Dialing and transmission problems 111 Reception and copying problems To close the printer compartment cover, grasp 112 113 General problems 114 Messages and Signals Memory is Full 115 116 Audible signals 117 Clearing Paper JamsClearing a jammed document Clearing jammed printing 118 119 120 Ordering Parts 121 FCC Regulatory Information 122 Entering Your Name and Number Setting the Date and TimeQuick Reference Guide Storing and Clearing Auto Dial Numbers 123 Sending FaxesReceiving Faxes Recording an Outgoing Message Memorización y borrado de números de marcación automática Guía de referencia rápidaIntroducción de su nombre y número Ajuste de la fecha y hora Recepción de mensajes telefax Transmisión de mensajes telefax125 126 A R P 127 Material Safety Data Sheet 2/2 128 129 130 Index 131 Index Remote Operation Card Limited Warranty Sharp Corporation