Lip Alpd,Alps | Sun Microsystems 5602 guide

5 – Managing Ports			0
5 – Managing Ports
Displaying Port Information


	Table 5-5. Port Statistics Data Window Entries (Continued)

	Entry		Description

	Class 3 Toss		Number of class 3 frames that were discarded by this port. A
			frame can be discarded because of detection of a missing
			frame (based on SEQ_CNT), detection of an E_D_TOV
			timeout, receiving a reject frame, or receiving a frame on an
			offline port.
	Class 3 Words In		Number of class 3 words received by this port.
	Class 3 Words Out		Number of class 3 words transmitted by this port.
	Decode Errors		Number of invalid transmission words detected during
			decoding. Decoding is from the 10-bit characters and special K
			characters.
	Ep Connects		Number of E_Port logins.
	FBusy		Number of class 2 and class 3 fabric busy (F_BSY) frames
			generated by this port in response to incoming frames. This
			usually indicates a busy condition on the fabric or N_port that
			is preventing delivery of this frame.
	Flow Errors		Number of times a frame is received and all the switch ports
			receive buffers are full. The normal Fabric Login exchange of
			flow control credit should prevent this from occurring. The
			frame will be discarded.
	FReject		Number of frames, from devices, that have been rejected.
			Frames can be rejected for any of a large number of reasons.
	Invalid CRC		Number of invalid Cyclic Redundancy Check (CRC) frames
			detected.
	Invalid Destination		Number of address identifier (S_ID, D_ID) errors. AL_PA
	Address		equals non-zero AL_PA found on F_Port.
	Link Failures		Number of optical link failures detected by this port. A link
			failure is a loss of synchronization or by loss of signal while not
			in the offline state. A loss of signal causes the switch to
			attempt to re-establish the link. If the link is not re-established,
			a link failure is counted. A link reset is performed after a link
			failure.
	LIP (AL_PD,AL_PS)		Number of F7, AL_PS LIPs, or AL_PD (vendor specific) resets,
			performed.
	LIP(f7,AL_PS)		This LIP is used to reinitialize the loop. An L_port, identified by
			AL_PS, may have noticed a performance degradation and is
			trying to restore the loop.

5-6	59097-01 A

Image 154

Sun Microsystems 5602 manual Lip Alpd,Alps

Contents

SANbox 5602 Switch Management User’s Guide SANbox 5602 Switch Management User’s Guide Document Revision History Table of Contents 12.1 Section Managing Fabrics11.6 12.2 4.1 5.15.2 3.1 Section Managing Switches Devices Data Window Switch Data Window 2.6 2.42.5 14.1 Appendix a Command Line Interface Section Managing Ports 109 Backing up and Restoring Switch Configurations106 112 Glossary Index Port Threshold Alarm Configuration Dialog Tables 134 Related Materials Intended AudienceJdom License Technical Support Training AvailabilityContact Information Introduction Technical Support 59097-01 a Using SANsurfer Switch Manager Workstation Requirements Installing the Management ApplicationWorkstation Requirements For a Linux platform SANsurfer Switch ManagerFor a Windows platform For a Solaris platform SANsurfer Management Suite SMS Installation for WindowsFor a Mac OS X platform Chglax.bat SMS Installation for Linux Chmod +x sansurferswitchmgrlinux5.02.xx.bin SMS Installation for Solaris Change directories to the package location Install the new SANsurfer Switch Manager packageLocate and execute the file sbmoversms.sh Starting SANsurfer Switch Manager ‰ For Linux or Solaris enter the SANsurfer command Initial Startup Dialog Exiting SANsurfer Switch Manager SANsurfer Switch Manager Window Uninstalling SANsurfer Switch Manager View file upon exit future SANsurfer Switch Manager sessions SMS Uninstall Installdirectory/UninstallData/SANsurferUninstaller Standalone Uninstall Changing the Encryption Key for the Default Fabric View File Setting SANsurfer Switch Manager Preferences Saving and Opening Fabric View Files Preferences Dialog SANsurfer Switch Manager Using Online Help Viewing Software Version and Copyright Information Topology Display SANsurfer Switch Manager User InterfaceFaceplate Display Menu Bars Topology Display Menu Faceplate Display Menu Shortcut Keys Tool Bar Tool Bar Buttons Fabric Tree Fabric Tree Graphic Window Working Status IndicatorData Window and Tabs Using the Topology Display Switch and Link Status Selecting Switches and Links Working with Switches and LinksArranging Switches in the Display Opening the Faceplate and Topology Display Popup Menus Topology Data Windows Using the Faceplate Display Port Views and Status Selecting Ports Working with PortsOpening the Faceplate Popup Menu Faceplate Data Windows Managing Fabrics Radius Servers Adding a Radius Server Add Radius Server Managing Fabrics Removing a Radius Server Remove Radius Server Editing Radius Server Information Edit Radius Server Information Modifying Authentication Order Radius Server Information Modify Authentication Order Radius Server Information Connection Security Securing a FabricFabric security consists of the following Security Consistency Checklist User Account Security Device Security Edit Security Dialog Edit Security Dialog Creating a Security Set Create Security Group Dialog Create Security Group Dialog Creating a Security Group Create Security Group Member Dialog Create a Security Group Member Dialog Creating a Security Group Member Editing the Security Configuration on a Switch Using the Security Config Dialog Viewing Properties of a Security Set, Group, or Member Activating a Security Set Archiving a Security Configuration to a FileDeactivating a Security Set Fabric Services Configured Security Data WindowActive Security Data Window Enabling In-band Management Enabling Snmp ConfigurationClick the In-band Management Enable button Tracking Fabric Firmware and Software Versions Viewing and Comparing Version Snapshots Exporting Version Snapshots to a File Managing the Fabric Database Adding a Fabric Removing a Fabric Opening a Fabric View File Saving a Fabric View File Deleting Switches and LinksRediscovering a Fabric Adding a New Switch to a Fabric Replacing a Failed Switch Displaying Fabric Information Fabric Status Topology Display Switch and Status Icons Switch Icon Description Displaying the Event Browser 11. Events Browser Severity Levels Description Icon Filtering the Event Browser 12. Filter Events Dialog Sorting the Event Browser Saving the Event Browser to a File Devices Data Window Devices Data Window Entries Active Zone Set Data Window 13. Active Zone Set Data Window Working with Device Information and Nicknames SANsurfer Switch Manager enables you to do the followingLink Data Window Displaying Detailed Device Information Managing Device Port Nicknames Exporting Device Information to a FileCreating a Nickname Deleting a Nickname Editing a NicknameExporting Nicknames to a File Zoning a Fabric Importing a Nicknames FileZoning Concepts Zones Soft Zones Aliases Access Control List Hard ZonesZone Sets Zoning Database Managing the Zoning Database Using the Zoning WizardManaging the zoning database consists of the following Editing the Zoning Database 15. Edit Zoning Dialog Managing Fabrics Zoning a Fabric Edit Zoning Dialog Tool Bar Buttons and Icons Configuring the Zoning Database Interop Auto Save Saving the Zoning Database to a File Default VisibilityDiscard Inactive Restoring the Zoning Database from a File Restoring the Default Zoning Database Removing All Zoning Definitions Managing Zone Sets Creating a Zone Set Activating and Deactivating a Zone Set Copying a Zone to a Zone Set Removing a Zone from a Zone Set or from All Zone Sets Removing a Zone Set Managing Zones Managing zones involves the following Creating a Zone in a Zone Set Adding Zone Members Removing a Zone from a Zone Set Renaming a Zone or a Zone SetRemoving a Zone Member Removing a Zone from All Zone Sets Managing Aliases Changing Zone TypesCreating an Alias Adding a Member to an Alias Removing an Alias from All Zones Merging Fabrics and Zoning Zone Merge Failure RecoveryZone Merge Failure Managing Switches Managing User Accounts Factory User Accounts User Account Administration Dialog Add Account Creating User Accounts User Account Administration Dialog Remove Account Removing a User Account Changing a User Account Password User Account Administration Dialog Change Password User Account Administration Dialog Modify Account Modifying a User Account Displaying Switch Information 5shows the faceplate display for the SANbox 5602 switch Switch Data Window Switch Data Window Entries Ratov Switch Data Window Entries Displaying Detailed Device Information on page 3-35for Port Statistics Data Window Port Information Data Window Configured Zonesets Data Window Configured Zonesets Data Window Configuring Port Threshold Alarms Port Threshold Alarm Configuration Dialog Count Paging a SwitchEvent Sample Window Setting the Date/Time and Enabling NTP Client Resetting a Switch Switch Resets Type Description Configuring a Switch Using the Configuration Wizard Switch Properties Symbolic Name Switch Administrative States Switch Administrative States Domain ID and Domain ID Lock Fabric Device Management Interface Broadcast Support In-band Management Advanced Switch Properties Interop Mode for Zoning Timeout Values Timeout ValuesLegacy Port Address Format System Services Dialog 11. System Services Dialog Security Consistency Checklist Dialog Network Properties 12. Network Properties Dialog IP Configuration IP Configuration Parameters Remote Logging NTP Client Snmp Properties 13. Snmp Properties Dialog Snmp Configuration Snmp Configuration Parameters Snmp Trap Configuration Snmp Trap Configuration Parameters Managing Switch Stacks 14. Switch Stacks Managing Switches Managing Switch Stacks Select Source Dialog SyslogInformation Archiving a Switch Restoring a Switch 16. Restore Dialogs Full and Selective Managing Switches Restoring a Switch Restoring the Factory Default Configuration Factory Default Configuration Settings Factory Default Configuration Settings Upgrading the Switch Using License Keys Downloading a Support File Installing Firmware 17. Features License Key Dialog Managing Switches Displaying Hardware Status 19. Hardware Status LEDs Managing Ports Displaying Port Information Displaying Port Types Monitoring Port StatusPort Types Port Operational States Displaying Port Operational StatesDisplaying Port Speeds Port Speeds Displaying Transceiver Media Status Port Transceiver Media View Port Statistics Data Window Entries LIP ALPD,ALPS Port Statistics Data Window Entries Port Information Data Window Entries Port Information Data Window Entries Configuring Ports Port Properties Dialog Changing Port Administrative States Port Administrative States Changing Port Speeds Changing Port Types Stream Guard Using the Extended Credits Wizard Changing Port Symbolic NameDevice Scan Resetting a Port Designate Donor Ports Testing Ports Port Loopback Test Dialog Managing Ports Graphing Port Performance Fabric View Graphs Starting SANsurfer Performance Viewer This section describes how to do the followingExiting SANsurfer Performance Viewer Save Default Performance View File Dialog Changing the Default Performance View File Encryption Key Saving and Opening Performance View Files Setting SANsurfer Performance Viewer Preferences Setting the Polling Frequency Displaying Graphs for a Switch Displaying Graphs for a Stack Arranging Graphs in the Display Customizing Graphs Managing Ports Printing Graphs Setting Global Graph TypeRescaling a Selected Graph Saving Graph Statistics to a File Command Line Interface Logging On to a Switch Working with Switch Configurations User Accounts Modifying a Configuration Backing up and Restoring Switch Configurations Ftp ipaddress Command keyword keyword value CommandsCommand syntax is as follows Table A-1. Command-Line Completion Table A-2. Commands Listed by Authority Level Admin Session Commands Syntax Admin CommandAuthority Keywords Alias Command Syntax alias Remove alias memberlist Members aliasRename aliasold aliasnew CIM Command CIMListener Command Table A-3. CIM Listener Configuration Parameters Following is an example of the CIMListener Create command Enter CIMSubscription Command Table A-4. CIM Subscription Configuration Parameters # cimsubscription create subscription1 Keywords activate configname Config CommandSyntax config Edit configname Restore command RestoreManager Archive function are not compatible with the Config Save configname #ftp symbolicname or ipaddress user images Certificate Create CommandCreate Support Command Line Interface Create Command Following is an example of the Create Certificate command Syntax date Date CommandKeywords MMDDhhmmCCYY Syntax feature Feature CommandAuthority Admin Command Line Interface Firmware Install Command Group Command Syntax group Keywords add group Table A-5. ISL Group Member Attributes Table A-6. Port Group Member Attributes Copy groupsource groupdestination Create group type Edit group member Table A-8. Group Member Attributes Rename groupold groupnew Members groupRemove group memberlist Securitysets group Following is an example of the Group Edit command ISL Following is an example of the Group List command Following is an example of the Group Members command Hardreset Command Syntax Syntax help command keyword Help CommandKeywords command Authority None History Command Authority None Syntax history Hotreset Command Hotreset Image Command Ftp Ftp switchname SANbox Manager admin # image install Wait for the unpack to complete Reinitializes the specified loop port Lip CommandFollowing is an example of the Lip command Lip portnumber Passwd Command Syntax passwd accountname Keywords accountname Ping Command Syntax ping ipaddress Keywords ipaddress Syntax Examples Ps CommandFollowing is an example of the Ps command Displays current system process information Closes the Telnet session Quit CommandSyntax quit, exit, or logout Reset Command Config configname Security ServicesSwitch Snmp Table A-9. Switch Configuration Defaults Values Table A-10. Port Configuration Defaults Parameter Gbps/2-Gbps Port Gbps Port Defaults Table A-11. Port Threshold Alarm Configuration Defaults Table A-12. Zoning Configuration Defaults Table A-13. Snmp Configuration Defaults Table A-14. Radius Configuration Defaults Table A-15. Services Configuration Defaults Table A-16. System Configuration Defaults Table A-17. Security Configuration Defaults Security Command Keywords active History MD5 Following is an example of the Security History command Following is an example of the Security Limits command Following is an example of the Security List command Securityset Command Remove securityset group Delete securitysetGroups securityset Rename securitysetold securitysetnew Set Command Syntax set Pagebreak state Setup optionSwitch state Port option Table A-18. Set Config Port Parameters Set Config CommandSet config Port portnumber Command Line Interface Set Config Command Table A-18. Set Config Port Parameters Table A-19. Security Configuration Parameters Table A-20. Set Config Switch Parameters Table A-20. Set Config Switch Parameters Table A-21. Set Config Threshold Parameters Threshold Table A-22. Set Config Zoning Parameters Arbff Enter key to do so Configuring Port Number AdminState Following is an example of the Set Config Security command Following is an example of the Set Config Switch command # set config switch Following is an example of the Set Config Threshold command Following is an example of the Set Config Zoning command Archive Set Log CommandSet log Component filterlist Snmp Display filter Start Level filterPort portlist Stop Alarms are always logged and always displayed on the screen Set Port Command State state Radius Services Snmp System Set Setup CommandSet setup Configuration fields Command Line Interface Set Setup Command Table A-24. Switch Services Settings Table A-24. Switch Services Settings Table A-25. Snmp Configuration Settings Table A-26. System Configuration Settings Table A-26. System Configuration Settings Following is an example of the Set Setup Services command Current value Following is an example of the Set Setup Snmp command Following is an example of the Set Setup System command Setup system Show Command Keywords about Cimsubscription subscriptionname Alarm optionCimlistener listenername Fdmi portwwn Ns option Log optionLsdb Pagebreak Table A-27. Show Port Parameters Tbuf LIPF8ALPS Post log Steering domainid Zoneset Active, List Table A-28. Switch Operational ParametersWhoami „ Zoning History, Limits, List Displays all connected devices Displays the current time zone settingTopology Users Following is an example of the Show Fabric command Following is an example of the Show Domains commandFollowing is an example of the Show Fdmi command Following is an example of the Show Fdmi WWN command Following is an example of the Show NS local domain command Following is an example of the Show NS portID command Following is an example of the Show NS domainID commandFollowing is an example of the Show Interface command Following is an example of the Show Port command PL-XPL-VC-SG3-22 Following is an example of the Show Switch command Following is an example of the Show Topology command 104 59097-01 a Following is an example of the Show Version command Show Config Command Show config Following is an example of the Show Config Switch command Following is an example of the Show Config Threshold command Following is an example of the Show Config Zoning command Show log Show Log CommandNone Keywords numberofevents Level SettingsZoning Monitors zoning conflict events Options Following is an example of the Show Log Options command Following is an example of the Show Log Level commandFollowing is an example of the Show Log command Portnumber Show Perf CommandShow perf Stop the display Following is an example of the Show Perf command Following is an example of the Show Perf Byte command Show setup Show Setup CommandMfg Following is an example of the Show Setup Radius command Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Power from the switch Shutdown CommandShutdown Port portnumber testtype Test CommandTest Status Admin start Test port x online Examples The following is an example of the Uptime command Uptime CommandAuthority None Syntax uptime Accounts User CommandUser Add Following is an example of the User Add command Following is an example of the User Edit command Following is an example of the User Delete command Following is an example of the User List command Following is an example of the Whoami command Whoami CommandWhoami Zone Command Syntax zone Rename zoneold zonenew Members zoneRemove zone memberlist Type zone zonetype Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Remove zoneset zonelist Following is an example of the Zoneset List commandFollowing is an example of the Zoneset Zones command Rename zonesetold zonesetnew Zoning Command Opens a Zoning Edit session Table A-29. Zoning Database Limits Limit Description Following is an example of the Zoning Limits command E1JBOD1 E2JBOD2 Following is an example of the Zoning List command Alarm Access Control List ZoneAdministrative State BootP Default Visibility Class 3 ServiceConfigured Zone Sets Fabric Management Switch Maintenance Button Input Power LEDInter-Switch Link Maintenance Mode Soft Zone Zoning DatabaseSmall Form-Factor Pluggable Target Index Index-2 59097-01 a 59097-01 a Index-3 Index-4 59097-01 a 59097-01 a Index-5 Index-6 59097-01 a 59097-01 a Index-7 Index-8 59097-01 a 59097-01 a Index-9 Index-10 59097-01 a