Part IV

Sequencer

5. Use the CURSOR

and

buttons to move

the cursor to the note position (dot) you are going to store.

Each dot represents one-eighth of a quarter-note (a thirty- second note).

When storing triplets, it may not be possible to match the timing exactly with the 1/32-note steps. However, if you select triplet-type notes for the note length (LENGTH) in step 6 below, the timing is automatically corrected.

6.Use the left REC NOTE LENGTH and buttons to specify the note value. Select from

3, , 3, , 3, , 3, , , , 2 to 4. (A 3 denotes a triplet-type note.)

For note values other than these, use the center REC NOTE LENGTH buttons to specify the note value to be added to that which you specified with the left buttons.

Example: To record a dotted quarter-note ( . )

+

7.Use the right REC NOTE LENGTH and buttons to specify the actual length of the pro- duced sound for the desired legato or staccato effect.

TENU (tenuto): Sound is produced for 95% of the note length.

NORM (normal): 80%

STAC (staccato): 50%

CUTT (cutting): 25%

Storing control data

Various control data can be stored at the cursor position.

1.On the STEP RECORD: MELODY display, press the CTL button.

2.Use the CTL and buttons to select the

control data you wish to insert.

Select from PAN, KEY SHIFT (COARSE TUNE), TUNING (FINE TUNE), BEND SENS.

3.Use the VALUE and buttons to adjust the numerical value of the setting.

4.Press YES button.

Correcting the data

1.In the STEP RECORD mode, specify the track you wish to correct.

2.Use the MEAS buttons to go to the measure you wish to modify. Use the CURSOR buttons to move the cursor to the point ( * ) you wish

to edit.

The data stored at that point is shown on the display.

When multiple data is stored at one point, different data is displayed in order each time a CURSOR button is pressed. When a chord is recorded, a different note in the chord is displayed each time a CURSOR button is pressed.

Sequencer

8.Specify the pitch and velocity of the note by

playing the keyboard.

The dot on the display where the note is stored changes to a * mark.

When recording chords, you can store multiple notes at one position.

Any panel setting changes—for example changes in the sound selection, button operation, etc.—are recorded at the cursor position.

When the TEMPO/PROGRAM dial is operated, the input value is indicated on the display. Confirm that this is the correct value and press the YES button to record the value or the NO button to cancel it.

BAL:

To specify the volume at the cursor position, after pressing the BAL button, use the VALUE buttons to set the volume (0 to 127).

ERS:

If you make a mistake, move the cursor to the error, and after displaying the data you wish to erase, press the ERS button.

REST:

To store a rest, after specifying the note LENGTH, press the REST button.

Positions at which nothing is stored are read as rests.

9.Repeat steps 5 through 8 to continue storing

notes.

To input data on another track, press the button for the desired track and repeat the procedure from step 2.

10.When you have finished recording, press the PROGRAM MENUS button to turn it off.

3.Correct the data.

There are three types of data:

Performance data

NOTE data (note pitch) and VEL data (how hard the key was played) and LEN data (1 = 1/96 of a quarter note [ ]) are displayed. Use the relevant buttons to correct the data as desired.

Sound data

The name of the sound is displayed. Change the sound as desired (the sound setting display is interposed on the current display).

Control data

The name of the function is displayed. Change the data as desired.

Press the ERS button to erase the data which is displayed.

You can also correct data which was stored in the REAL- TIME RECORD mode.

Performance (NOTE) data can be recorded or edited on a piano roll display. (Refer to page 78.)

72

QQTG0665

Page 72
Image 72
Technics sx-PR604/M Storing control data, Correcting the data, Repeat steps 5 through 8 to continue storing, Control data