Query Error List | Xantrex Technology GPIB-M-XPD, GPIB-M-XHR

Error Messages

Query Error List

Query Error List

An error number in the range [-499, -400] indicates that the output queue control of the instrument has detected a problem with the message exchange protocol described in IEEE 488.2, chapter 6. The occurrence of any error in this class causes the query error bit (bit 2) in the Event Status Register to be set.

Table C.4 Query Error List

Error	Error Message Description
code	Error Message Description
-400	Query Error
	This is the generic query error for the power supply, used only when the other
	types of errors do not apply.

-410	Query INTERRUPTED
	Generated when a new command was received before it could finish the query.

User Request Event

An error/event in the range [-699, -600] is used when the instrument wishes to report a 488.2 user request event. This event also sets the user request bit (bit 6) of the Standard Event Status Register.

Table C.5 User Request Event

Errorcode Error Message Description

-600 User request

Operation Complete Event

An error/event in the range [-899, -800] is used when the instrument wishes to report a 488.2 operation complete event. This event occurs when an instrument’s synchronization protocol, having been enabled by an *OPC command, completes all selected pending operations. This event also sets the operation complete bit (bit 0) of the Standard Event Status Register.

Table C.6 Operation Complete Event

Errorcode Error Message Description

-800 Operation complete

Release 2.1

121

Image 123

Xantrex Technology GPIB-M-XPD, GPIB-M-XHR, GPIB-M-XFR manual Query Error List, User Request Event, Operation Complete Event

Contents

Operating Manual Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service? What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power Supply Supply Safety Installation and Configuration Describes the power supply and listsIts features and specifications Gives basic setup procedures Power Supply Safety Markings Manual RevisionsAbout This Manual Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Description Features and Functions Features and Specifications FunctionsReadback Models 15-20 30-10 60-5 Specifications Models 60-20 100-12 150-8 300-4 600-2 Models 140 12-100 20-60 35-35 40-30 Models 60-46 100-28 150-18 300-9 600-4 Models 300 12-220 20-130 33-85 40-70 Models 100-10 150-7 300-3.5 600-1.7 Models 130 20-50 33-33 40-25 60-18 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Models 18-30 33-16 60-9 120-4.5 Features and Specifications Initial Inspection Introduction XFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface Basic Setup Procedure To install the ferrite blockIEEE-488 Controller Connection Power on Power on the unit Configure Computer Controller Configure power supplyTest Feature Factory Preset Value Change Remote Control Source Configure for Gpib Operation Example Configure for Multichannel Operation Interface CANbusCables CAN-only Using OperationMultichannel Appendix B. Scpi Command Reference lists all commands Specifications Pin # Function Input/Output User Lines XT, HPD XPD User Lines Connection 13Schematic For User Line Interface Overview Powering on Supply Operation Power Supply Operating States Power Supply Regulation Modes Remote Control Modes Description Front Panel LEDs Changing the remote/local state Power Supply OperationTo query to remote mode Mode To query the state of the output enable To enable or disable the output MEASVOLT? MEASCURR? Configure Output Protection To set the fold delay To set the fold mode To query if OTP has tripped Set Shutdown Recovery for AC OffAdditional Protections To query if AC Off has tripped Clear Protection Event Shutdown vs Protection Alarm To store save settings To recall settingsTo save default settings To power on user setting #1 To change the power on at output state To reset the unitFeature Reset State *RST To read from the error queue ConfigureAuxiliary To set up Auxiliary line a To set up Auxiliary line BTo check the state of the line Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command To set the voltage limits To set the current limitsTriggered To set a triggered setpoint To program triggers Operation Identification Query Option Identification Query Register Status Registers Status Registers Operation Status Registers Bit Bit Weight Bit Name Description BitBit Name Description Protection SHUTdown Sub-Register Bit Bit Weight Bit Name Description Current SHareSub-Register Questionable Status Registers Time Sub-Register Table Summarizes the standard Event Status Register Been lost. See Query Error List on QSR Request ServiceMaster Summary Status Register Commands CommandsRegister Filter/Enable Preset Value Scpi equivalent for multichannel use Ieee Status Event Commands STB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? Questionable STATchannelOPERCSHEVEN? Commands STATchannelQUESVOLTCOND? Current Sharing Current Sharing No sharing Operation Current Sharing Address Range Service Request and PollingCodes and Standards Message Terminators Protocol Specifications Control FunctionsFunction Mnemonic Description Functions Subset Signal Driver Line Electrical SpecificationsMechanical Specifications Performance Specifications Performance Specifications Appendix B. Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Scpi Command Reference Understanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Used Scpi Command SummaryNotations Tables Table B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 112 Table B.12User Lines Table B.14Auto Sequence Commands StepnumberDELete Expression Details Expressions Expressions Appendix C. Error Messages Errorcode Error Message Description Command Error ListExecution Error List Error Messages Execution Error List Error Error Message Description Code Device-Specific Error List Query Error List User Request EventOperation Complete Event Auto Sequencing Error Codes Front Panel Error CodesCPU Error Codes Analog Programming Interface Error codes Multichannel Error Codes CANbus Error Codes Current Share Error Codes Appendix D. Calibration Entering Calibration Mode Calibration Setup and Equipment Output Voltage Calibration Procedure Enter current data Restore Factory Calibration Exit calibration mode Restore Factory Calibration Page Xantrex Technology Inc