Execution Error List | Xantrex Technology GPIB-M-XFR, GPIB-M-XHR

Error Messages

Execution Error List

Errorcode Error Message Description

-220 Parameter error

Indicates that a program data element related error occurred.

-221 Setting conflict

Indicates that a legal program data element was parsed but could not be executed due to the current power supply state.

Factors that may contribute to this error are:

Remote source - To set most values, the remote source must be correct. Remote state - To set most values, the unit must be in remote mode. Calibration mode - when in calibration mode, certain settings will cause as error. Current share mode - When the unit is in current share mode (other than none) certain settings will cause an error.

-222 Data out of range

Indicates that a legal command could not be executed because the interpreted value was outside the legal range as defined by the power supply.

-225 Out of memory

The power supply has insufficient memory to perform the requested operation.

-231 Data questionable

Indicates that measurement accuracy is suspect.

-240 Hardware error (occurs during flash update if there is a failure) Indicates that a legal program command or query could not be executed because of a hardware problem in the power supply.

-241 Hardware missing

Indicates that a legal program command or query could not be executed because of missing power supply hardware; e.g. an option not installed.

-282 Illegal program name

The name used to reference an auto sequence program was invalid or there is no program selected.

-284 Program currently running

Certain operations dealing with auto sequence programs may be illegal while the program is running. For example, deleting a running program is not possible.

-285 Program syntax error

There is an error in the program definition.

-290 Memory use error

Indicates that a user request has directly or indirectly caused an error related to memory or <data_handle>s. This is not the same as “bad” memory.

Release 2.1

119

Image 121

Xantrex Technology GPIB-M-XHR, GPIB-M-XT, GPIB-M-XPD, GPIB-M-XFR3, GPIB-M-HPD manual Execution Error List

Contents

Operating Manual Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service? What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power Supply Supply Safety Its features and specifications Describes the power supply and listsGives basic setup procedures Installation and Configuration Manual Revisions Power Supply Safety MarkingsAbout This Manual Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Description Features and Functions Functions Features and SpecificationsReadback Models 15-20 30-10 60-5 Specifications Models 60-20 100-12 150-8 300-4 600-2 Models 140 12-100 20-60 35-35 40-30 Models 60-46 100-28 150-18 300-9 600-4 Models 300 12-220 20-130 33-85 40-70 Models 100-10 150-7 300-3.5 600-1.7 Models 130 20-50 33-33 40-25 60-18 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Models 18-30 33-16 60-9 120-4.5 Features and Specifications Initial Inspection Introduction XFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface To install the ferrite block Basic Setup ProcedureIEEE-488 Controller Connection Configure power supply Power on Power on the unit Configure Computer ControllerTest Feature Factory Preset Value Change Remote Control Source Configure for Gpib Operation Example Configure for Multichannel Operation Cables CANbusCAN-only Interface Operation UsingMultichannel Appendix B. Scpi Command Reference lists all commands Specifications Pin # Function Input/Output User Lines XT, HPD XPD User Lines Connection 13Schematic For User Line Interface Overview Powering on Supply Operation Power Supply Operating States Power Supply Regulation Modes Remote Control Modes Description Front Panel LEDs To query to remote mode Power Supply OperationMode Changing the remote/local state To query the state of the output enable To enable or disable the output MEASVOLT? MEASCURR? Configure Output Protection To set the fold delay To set the fold mode Additional Protections Set Shutdown Recovery for AC OffTo query if AC Off has tripped To query if OTP has tripped Clear Protection Event Shutdown vs Protection Alarm To recall settings To store save settingsTo save default settings To power on user setting #1 To reset the unit To change the power on at output stateFeature Reset State *RST Configure To read from the error queueAuxiliary To set up Auxiliary line B To set up Auxiliary line aTo check the state of the line Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command To set the current limits To set the voltage limitsTriggered To set a triggered setpoint To program triggers Operation Identification Query Option Identification Query Register Status Registers Status Registers Operation Status Registers Bit Bit Bit Weight Bit Name DescriptionBit Name Description Protection SHUTdown Sub-Register Bit Bit Weight Bit Name Description SHare CurrentSub-Register Questionable Status Registers Time Sub-Register Table Summarizes the standard Event Status Register Been lost. See Query Error List on QSR Master ServiceSummary Request Commands Status Register CommandsRegister Filter/Enable Preset Value Scpi equivalent for multichannel use Ieee Status Event Commands STB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? Questionable STATchannelOPERCSHEVEN? Commands STATchannelQUESVOLTCOND? Current Sharing Current Sharing No sharing Operation Current Sharing Codes and Standards Service Request and PollingMessage Terminators Address Range Control Functions Protocol SpecificationsFunction Mnemonic Description Functions Subset Mechanical Specifications Electrical SpecificationsPerformance Specifications Signal Driver Line Performance Specifications Appendix B. Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Scpi Command Reference Understanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Notations Scpi Command SummaryTables Used Table B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 112 Table B.12User Lines Table B.14Auto Sequence Commands StepnumberDELete Expression Details Expressions Expressions Appendix C. Error Messages Execution Error List Command Error ListError Messages Errorcode Error Message Description Execution Error List Error Error Message Description Code Device-Specific Error List User Request Event Query Error ListOperation Complete Event CPU Error Codes Front Panel Error CodesAnalog Programming Interface Error codes Auto Sequencing Error Codes Multichannel Error Codes CANbus Error Codes Current Share Error Codes Appendix D. Calibration Entering Calibration Mode Calibration Setup and Equipment Output Voltage Calibration Procedure Enter current data Restore Factory Calibration Exit calibration mode Restore Factory Calibration Page Xantrex Technology Inc