CANbus Error Codes | Xantrex Technology GPIB-M-HPD, GPIB-M-XHR

Error Messages

CANbus Error Codes

CANbus Error Codes

Table C.11CANbus Error Codes

	Error	Error Message Description
	code	Error Message Description
	code
	+1701	CANbus hardware missing
		The CANbus option is not installed on the controller card, or controller card is
		not present.
	+1702	CANbus device specific error
		An error has occurred on the CANbus circuit. Probable causes are AC input
		too low, AC input not secure, controller card not securely fastened or other
		noise sources.
	+1703	CANbus input buffer corrupted.

	+1704	CANbus input buffer corrupted.

	+1705	CANbus input buffer overrun.
		Data is sent on the CANbus faster than the CPU can process.

	+1706	CANbus output buffer overrun.
		Data cannot be transmitted fast enough.

Multichannel Error Codes

Table C.12Multichannel Error Codes

	Error	Error Message Description
	code	Error Message Description
	code
	+1800	Multichannel general error
		An error has occurred while sending multichannel commands. One such
		cause is sending a command that is too long.

	+1802	Multichannel address taken
		The multichannel address configured for this unit has already been assigned
		to another unit on the CANbus network.

	+1803	Multichannel originator not responding
		The originator of the message is not responding to the handshaking.
	+1804	Multichannel recipient not responding
		The recipient of the message is not acknowledging the reception of the
		command.
	+1805	Multichannel command overwritten
		A received command through the CANbus has been overwritten.

Release 2.1

123

Image 125

Xantrex Technology GPIB-M-HPD, GPIB-M-XHR, GPIB-M-XFR, GPIB-M-XT, GPIB-M-XPD CANbus Error Codes, Multichannel Error Codes

Contents

Operating Manual Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service? What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power Supply Supply Safety Its features and specifications Describes the power supply and listsGives basic setup procedures Installation and Configuration About This Manual Power Supply Safety MarkingsManual Revisions Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Description Features and Functions Readback Features and SpecificationsFunctions Models 15-20 30-10 60-5 Specifications Models 60-20 100-12 150-8 300-4 600-2 Models 140 12-100 20-60 35-35 40-30 Models 60-46 100-28 150-18 300-9 600-4 Models 300 12-220 20-130 33-85 40-70 Models 100-10 150-7 300-3.5 600-1.7 Models 130 20-50 33-33 40-25 60-18 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Models 18-30 33-16 60-9 120-4.5 Features and Specifications Initial Inspection Introduction XFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface IEEE-488 Controller Connection Basic Setup ProcedureTo install the ferrite block Test Power on Power on the unit Configure Computer ControllerConfigure power supply Feature Factory Preset Value Change Remote Control Source Configure for Gpib Operation Example Configure for Multichannel Operation Cables CANbusCAN-only Interface Multichannel UsingOperation Appendix B. Scpi Command Reference lists all commands Specifications Pin # Function Input/Output User Lines XT, HPD XPD User Lines Connection 13Schematic For User Line Interface Overview Powering on Supply Operation Power Supply Operating States Power Supply Regulation Modes Remote Control Modes Description Front Panel LEDs To query to remote mode Power Supply OperationMode Changing the remote/local state To query the state of the output enable To enable or disable the output MEASVOLT? MEASCURR? Configure Output Protection To set the fold delay To set the fold mode Additional Protections Set Shutdown Recovery for AC OffTo query if AC Off has tripped To query if OTP has tripped Clear Protection Event Shutdown vs Protection Alarm To save default settings To store save settingsTo recall settings To power on user setting #1 Feature Reset State *RST To change the power on at output stateTo reset the unit Auxiliary To read from the error queueConfigure To check the state of the line To set up Auxiliary line aTo set up Auxiliary line B Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command Triggered To set a triggered setpoint To set the voltage limitsTo set the current limits To program triggers Operation Identification Query Option Identification Query Register Status Registers Status Registers Operation Status Registers Bit Name Description Bit Bit Weight Bit Name DescriptionBit Protection SHUTdown Sub-Register Bit Bit Weight Bit Name Description Sub-Register CurrentSHare Questionable Status Registers Time Sub-Register Table Summarizes the standard Event Status Register Been lost. See Query Error List on QSR Master ServiceSummary Request Register Filter/Enable Preset Value Status Register CommandsCommands Scpi equivalent for multichannel use Ieee Status Event Commands STB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? Questionable STATchannelOPERCSHEVEN? Commands STATchannelQUESVOLTCOND? Current Sharing Current Sharing No sharing Operation Current Sharing Codes and Standards Service Request and PollingMessage Terminators Address Range Function Mnemonic Description Functions Subset Protocol SpecificationsControl Functions Mechanical Specifications Electrical SpecificationsPerformance Specifications Signal Driver Line Performance Specifications Appendix B. Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Scpi Command Reference Understanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Notations Scpi Command SummaryTables Used Table B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 112 Table B.12User Lines Table B.14Auto Sequence Commands StepnumberDELete Expression Details Expressions Expressions Appendix C. Error Messages Execution Error List Command Error ListError Messages Errorcode Error Message Description Execution Error List Error Error Message Description Code Device-Specific Error List Operation Complete Event Query Error ListUser Request Event CPU Error Codes Front Panel Error CodesAnalog Programming Interface Error codes Auto Sequencing Error Codes Multichannel Error Codes CANbus Error Codes Current Share Error Codes Appendix D. Calibration Entering Calibration Mode Calibration Setup and Equipment Output Voltage Calibration Procedure Enter current data Restore Factory Calibration Exit calibration mode Restore Factory Calibration Page Xantrex Technology Inc