Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology GPIB-M-XHR, GPIB-M-XFR, GPIB-M-XT, GPIB-M-XPD manual Restore Factory Calibration

Models: GPIB-M-XT GPIB-M-XFR GPIB-M-XFR3 GPIB-M-XHR GPIB-M-XPD GPIB-M-HPD

1 134

Download 134 pages 21.51 Kb

Specification Install Error codes Shutdown vs Protection Alarm To save default settings To set the fold delay Configure power supply Feature Factory Preset Value Basic Setup Procedure Status Register Commands

Page 132

Calibration

Restore Factory Calibration

130	Operating Manual for Multichannel Functionality (GPIB-M)

Page 131 Page 133

Image 132

Xantrex Technology GPIB-M-XHR, GPIB-M-XT, GPIB-M-XPD, GPIB-M-XFR3, GPIB-M-HPD manual Restore Factory Calibration

Page 131 Page 133

Our partner
Обсуждение вопроса Были ли случаи закрытия частных школ за нарушения? из чата CY Law, Visas, Taxes, Insurance, Кипр

Related pages All Recover page Performing a recovery for Compaq 615 Samsung Recovery Solution 可选 for Samsung NP-N150-JA03PT Data Recovery Services Authorized Service Centers for Seagate 7200.11 Backing up and recovering your data for HP 7 Extreme System Recovery for Toshiba L40t-B Recovering a Non-System Disk or Partition for Freedom9 4020 Restore for Vivotek 4X-IP7142 System Restore for Dell KYX1Y Recovering from a POST/BIOS update failure for Lenovo 6306 Performing a Recovery for HP C318LA What is the APC authentication phrase used for in SNMPv3? Learn more

Contents

Operating Manual Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase Date Safety Supply Describes the power supply and lists Its features and specificationsGives basic setup procedures Installation and Configuration Power Supply Safety Markings Manual RevisionsAbout This Manual Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Features and Functions Description Features and Specifications FunctionsReadback Specifications Models 15-20 30-10 60-5 Models 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Models 18-30 33-16 60-9 120-4.5 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Features and Specifications Introduction Initial Inspection XFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface Basic Setup Procedure To install the ferrite blockIEEE-488 Controller Connection Power on Power on the unit Configure Computer Controller Configure power supplyTest Feature Factory Preset Value Configure for Gpib Operation Change Remote Control Source Configure for Multichannel Operation Example CANbus CablesCAN-only Interface Using OperationMultichannel Appendix B. Scpi Command Reference lists all commands Specifications User Lines Pin # Function Input/Output User Lines Connection XT, HPD XPD 13Schematic For User Line Interface Powering on Supply Overview Power Supply Operating States Operation Power Supply Regulation Modes Remote Control Modes Front Panel LEDs Description Power Supply Operation To query to remote modeMode Changing the remote/local state To enable or disable the output To query the state of the output enable MEASVOLT? MEASCURR? Configure Output Protection To set the fold mode To set the fold delay Set Shutdown Recovery for AC Off Additional ProtectionsTo query if AC Off has tripped To query if OTP has tripped Shutdown vs Protection Alarm Clear Protection Event To store save settings To recall settingsTo save default settings To power on user setting #1 To change the power on at output state To reset the unitFeature Reset State *RST To read from the error queue ConfigureAuxiliary To set up Auxiliary line a To set up Auxiliary line BTo check the state of the line Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command To set the voltage limits To set the current limitsTriggered To set a triggered setpoint To program triggers Operation Option Identification Query Identification Query Status Registers Register Status Registers Operation Status Registers Bit Bit Weight Bit Name Description BitBit Name Description Sub-Register Bit Bit Weight Bit Name Description Protection SHUTdown Current SHareSub-Register Questionable Status Registers Sub-Register Table Time Summarizes the standard Event Status Register Been lost. See Query Error List on QSR Service MasterSummary Request Status Register Commands CommandsRegister Filter/Enable Preset Value Ieee Status Event Commands Scpi equivalent for multichannel use STB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? STATchannelOPERCSHEVEN? Questionable Commands STATchannelQUESVOLTCOND? Current Sharing No sharing Current Sharing Operation Current Sharing Service Request and Polling Codes and StandardsMessage Terminators Address Range Protocol Specifications Control FunctionsFunction Mnemonic Description Functions Subset Electrical Specifications Mechanical SpecificationsPerformance Specifications Signal Driver Line Performance Specifications Appendix B. Scpi Command Reference Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Understanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Scpi Command Summary NotationsTables Used Table B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 Table B.12User Lines 112 Table B.14Auto Sequence Commands StepnumberDELete Expressions Expression Details Expressions Appendix C. Error Messages Command Error List Execution Error ListError Messages Errorcode Error Message Description Execution Error List Device-Specific Error List Error Error Message Description Code Query Error List User Request EventOperation Complete Event Front Panel Error Codes CPU Error CodesAnalog Programming Interface Error codes Auto Sequencing Error Codes CANbus Error Codes Multichannel Error Codes Current Share Error Codes Entering Calibration Mode Appendix D. Calibration Setup and Equipment Calibration Calibration Procedure Output Voltage Enter current data Exit calibration mode Restore Factory Calibration Restore Factory Calibration Page Xantrex Technology Inc

Top Page Image Contents