Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology GPIB-M-XFR, GPIB-M-XHR To set the voltage limits, To set the current limits

Models: GPIB-M-XT GPIB-M-XFR GPIB-M-XFR3 GPIB-M-XHR GPIB-M-XPD GPIB-M-HPD

1 134

Download 134 pages 21.51 Kb

Page 67

Operation

Auto Sequencing

Set V, I, and P The voltage, current and power setpoints can be limited to less than the supply rating Limits range to match the tolerance of connected equipment or any other criteria you may

have.

Once the limits have been changed from the supply’s default rated output, settings outside this range are no longer accepted.

Note Setpoint limits do not apply to the triggered outputs and auto sequence outputs.

To set the voltage limits:

SOUR:VOLT:LIM:HIGH <voltage>

SOUR:VOLT:LIM:LOW <voltage>

To set the current limits:

SOUR:CURR:LIM:HIGH <current>

SOUR:CURR:LIM:LOW <current>

If the high end of the range was set to 5 volts, the command, SOUR:VOLT 10 would return an error.

Triggered To set a triggered setpoint:

Setpoints SOUR:VOLT:TRIG <voltage>

SOUR:CURR:TRIG <current>

See “Triggering Commands” on page 66 for more information.

Release 2.1

65

Image 67

Xantrex Technology GPIB-M-XFR To set the voltage limits, To set the current limits, Triggered To set a triggered setpoint

Contents

Operating Manual Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service?What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplySupply SafetyInstallation and Configuration Describes the power supply and listsIts features and specifications Gives basic setup proceduresManual Revisions Power Supply Safety MarkingsAbout This Manual Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Description Features and FunctionsFunctions Features and SpecificationsReadback Models 15-20 30-10 60-5 SpecificationsModels 60-20 100-12 150-8 300-4 600-2 Models 140 12-100 20-60 35-35 40-30Models 60-46 100-28 150-18 300-9 600-4 Models 300 12-220 20-130 33-85 40-70Models 100-10 150-7 300-3.5 600-1.7 Models 130 20-50 33-33 40-25 60-18Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Models 18-30 33-16 60-9 120-4.5Features and Specifications Initial Inspection IntroductionXFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface To install the ferrite block Basic Setup ProcedureIEEE-488 Controller Connection Configure power supply Power on Power on the unit Configure Computer ControllerTest Feature Factory Preset Value Change Remote Control Source Configure for Gpib OperationExample Configure for Multichannel OperationInterface CANbusCables CAN-onlyOperation UsingMultichannel Appendix B. Scpi Command Reference lists all commands Specifications Pin # Function Input/Output User LinesXT, HPD XPD User Lines Connection13Schematic For User Line Interface Overview Powering on SupplyOperation Power Supply Operating StatesPower Supply Regulation Modes Remote Control Modes Description Front Panel LEDsChanging the remote/local state Power Supply OperationTo query to remote mode ModeTo query the state of the output enable To enable or disable the outputMEASVOLT? MEASCURR? Configure Output Protection To set the fold delay To set the fold modeTo query if OTP has tripped Set Shutdown Recovery for AC OffAdditional Protections To query if AC Off has trippedClear Protection Event Shutdown vs Protection AlarmTo recall settings To store save settingsTo save default settings To power on user setting #1 To reset the unit To change the power on at output stateFeature Reset State *RST Configure To read from the error queueAuxiliary To set up Auxiliary line B To set up Auxiliary line aTo check the state of the line Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command To set the current limits To set the voltage limitsTriggered To set a triggered setpoint To program triggers Operation Identification Query Option Identification QueryRegister Status RegistersStatus Registers Operation Status Registers Bit Bit Bit Weight Bit Name DescriptionBit Name Description Protection SHUTdown Sub-Register Bit Bit Weight Bit Name DescriptionSHare CurrentSub-Register Questionable Status Registers Time Sub-Register TableSummarizes the standard Event Status Register Been lost. See Query Error List on QSR Request ServiceMaster SummaryCommands Status Register CommandsRegister Filter/Enable Preset Value Scpi equivalent for multichannel use Ieee Status Event CommandsSTB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? Questionable STATchannelOPERCSHEVEN?Commands STATchannelQUESVOLTCOND? Current Sharing Current Sharing No sharingOperation Current Sharing Address Range Service Request and PollingCodes and Standards Message TerminatorsControl Functions Protocol SpecificationsFunction Mnemonic Description Functions Subset Signal Driver Line Electrical SpecificationsMechanical Specifications Performance SpecificationsPerformance Specifications Appendix B. Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Scpi Command ReferenceUnderstanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Used Scpi Command SummaryNotations TablesTable B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 112 Table B.12User LinesTable B.14Auto Sequence Commands StepnumberDELete Expression Details ExpressionsExpressions Appendix C. Error Messages Errorcode Error Message Description Command Error ListExecution Error List Error MessagesExecution Error List Error Error Message Description Code Device-Specific Error ListUser Request Event Query Error ListOperation Complete Event Auto Sequencing Error Codes Front Panel Error CodesCPU Error Codes Analog Programming Interface Error codesMultichannel Error Codes CANbus Error CodesCurrent Share Error Codes Appendix D. Calibration Entering Calibration ModeCalibration Setup and EquipmentOutput Voltage Calibration ProcedureEnter current data Restore Factory Calibration Exit calibration modeRestore Factory Calibration Page Xantrex Technology Inc