Example, Specifications | Xantrex Technology GPIB-M-HPD, GPIB-M-XHR

Installation and Configuration

Configure for Multichannel Operation

Broadcasting You can specify a channel address of "0" to broadcast a command to all power Commands supplies connect via CANbus. Broadcast commands are useful in set up and

operation.

Example:

Set all power supplies to remote mode:

SYST0:REM:STAT REM

Turn output on:

OUTP0 ON

Set voltage output to maximum:

SOUR0:VOLT MAX

Attempting to broadcast any query will generate an error.

Note Broadcasting may be useful in configuring a CAN-only power supply when its address is unknown. Connect the unit to a GPIB-M power supply. Broadcast the set multichannel command to change the CAN-only supply's address. The command has no effect on the GPIB controlled unit.

Example: "SYST0:COMM:MCH:ADDR 2" will set the CAN-only unit to address 2.

Note that there will be a lag in execution time between the local unit and all other units of up to a maximum of 20 ms.

Specifications

Max connected units	50
Max cable length	40 m

Bus speed	700 kbits/sec

Termination	120 ohm 1/4 W

Connectors	modular handset 4-position, 4-contact jacks
Addresses	1 to 50

Release 2.1

39

Image 41

Xantrex Technology GPIB-M-HPD, GPIB-M-XHR, GPIB-M-XT, GPIB-M-XPD, GPIB-M-XFR3 manual Example, Specifications

Contents

Operating Manual Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service? What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power Supply Supply Safety Its features and specifications Describes the power supply and listsGives basic setup procedures Installation and Configuration About This Manual Power Supply Safety MarkingsManual Revisions Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Description Features and Functions Readback Features and SpecificationsFunctions Models 15-20 30-10 60-5 Specifications Models 60-20 100-12 150-8 300-4 600-2 Models 140 12-100 20-60 35-35 40-30 Models 60-46 100-28 150-18 300-9 600-4 Models 300 12-220 20-130 33-85 40-70 Models 100-10 150-7 300-3.5 600-1.7 Models 130 20-50 33-33 40-25 60-18 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Models 18-30 33-16 60-9 120-4.5 Features and Specifications Initial Inspection Introduction XFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface IEEE-488 Controller Connection Basic Setup ProcedureTo install the ferrite block Test Power on Power on the unit Configure Computer ControllerConfigure power supply Feature Factory Preset Value Change Remote Control Source Configure for Gpib Operation Example Configure for Multichannel Operation Cables CANbusCAN-only Interface Multichannel UsingOperation Appendix B. Scpi Command Reference lists all commands Specifications Pin # Function Input/Output User Lines XT, HPD XPD User Lines Connection 13Schematic For User Line Interface Overview Powering on Supply Operation Power Supply Operating States Power Supply Regulation Modes Remote Control Modes Description Front Panel LEDs To query to remote mode Power Supply OperationMode Changing the remote/local state To query the state of the output enable To enable or disable the output MEASVOLT? MEASCURR? Configure Output Protection To set the fold delay To set the fold mode Additional Protections Set Shutdown Recovery for AC OffTo query if AC Off has tripped To query if OTP has tripped Clear Protection Event Shutdown vs Protection Alarm To save default settings To store save settingsTo recall settings To power on user setting #1 Feature Reset State *RST To change the power on at output stateTo reset the unit Auxiliary To read from the error queueConfigure To check the state of the line To set up Auxiliary line aTo set up Auxiliary line B Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command Triggered To set a triggered setpoint To set the voltage limitsTo set the current limits To program triggers Operation Identification Query Option Identification Query Register Status Registers Status Registers Operation Status Registers Bit Name Description Bit Bit Weight Bit Name DescriptionBit Protection SHUTdown Sub-Register Bit Bit Weight Bit Name Description Sub-Register CurrentSHare Questionable Status Registers Time Sub-Register Table Summarizes the standard Event Status Register Been lost. See Query Error List on QSR Master ServiceSummary Request Register Filter/Enable Preset Value Status Register CommandsCommands Scpi equivalent for multichannel use Ieee Status Event Commands STB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? Questionable STATchannelOPERCSHEVEN? Commands STATchannelQUESVOLTCOND? Current Sharing Current Sharing No sharing Operation Current Sharing Codes and Standards Service Request and PollingMessage Terminators Address Range Function Mnemonic Description Functions Subset Protocol SpecificationsControl Functions Mechanical Specifications Electrical SpecificationsPerformance Specifications Signal Driver Line Performance Specifications Appendix B. Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Scpi Command Reference Understanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Notations Scpi Command SummaryTables Used Table B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 112 Table B.12User Lines Table B.14Auto Sequence Commands StepnumberDELete Expression Details Expressions Expressions Appendix C. Error Messages Execution Error List Command Error ListError Messages Errorcode Error Message Description Execution Error List Error Error Message Description Code Device-Specific Error List Operation Complete Event Query Error ListUser Request Event CPU Error Codes Front Panel Error CodesAnalog Programming Interface Error codes Auto Sequencing Error Codes Multichannel Error Codes CANbus Error Codes Current Share Error Codes Appendix D. Calibration Entering Calibration Mode Calibration Setup and Equipment Output Voltage Calibration Procedure Enter current data Restore Factory Calibration Exit calibration mode Restore Factory Calibration Page Xantrex Technology Inc