Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology GPIB-M-XFR3, GPIB-M-XHR, GPIB-M-XT, GPIB-M-XPD, GPIB-M-HPD Measvolt? Meascurr?

Models: GPIB-M-XT GPIB-M-XFR GPIB-M-XFR3 GPIB-M-XHR GPIB-M-XPD GPIB-M-HPD

1 134

Download 134 pages 21.51 Kb

Page 52

Operation

Power Supply Operation

Readback To check the voltage or current output of the power supply, use the commands:

MEAS:VOLT?

MEAS:CURR?

Units are in volts and amps, respectively.

Example:

To set voltage to 5.5V and current limit to 100A, send the command: :VOLT 5.5; :CURR 100

Then check the output:

MEAS:VOLT? 5.500 (example readback, default unit V)

MEAS:CURR? 0.010 (example readback, default unit A)

50	Operating Manual for Multichannel Functionality (GPIB-M)

Image 52

Xantrex Technology GPIB-M-XFR3, GPIB-M-XHR, GPIB-M-XT, GPIB-M-XPD, GPIB-M-HPD manual Measvolt? Meascurr?

Contents

Operating Manual Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase DateSafety SupplyDescribes the power supply and lists Its features and specificationsGives basic setup procedures Installation and ConfigurationManual Revisions Power Supply Safety MarkingsAbout This Manual Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Features and Functions DescriptionFunctions Features and SpecificationsReadback Specifications Models 15-20 30-10 60-5Models 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7Models 18-30 33-16 60-9 120-4.5 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25Features and Specifications Introduction Initial InspectionXFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface To install the ferrite block Basic Setup ProcedureIEEE-488 Controller Connection Configure power supply Power on Power on the unit Configure Computer ControllerTest Feature Factory Preset Value Configure for Gpib Operation Change Remote Control SourceConfigure for Multichannel Operation ExampleCANbus CablesCAN-only InterfaceOperation UsingMultichannel Appendix B. Scpi Command Reference lists all commands Specifications User Lines Pin # Function Input/OutputUser Lines Connection XT, HPD XPD13Schematic For User Line Interface Powering on Supply OverviewPower Supply Operating States OperationPower Supply Regulation Modes Remote Control Modes Front Panel LEDs DescriptionPower Supply Operation To query to remote modeMode Changing the remote/local stateTo enable or disable the output To query the state of the output enableMEASVOLT? MEASCURR? Configure Output Protection To set the fold mode To set the fold delaySet Shutdown Recovery for AC Off Additional ProtectionsTo query if AC Off has tripped To query if OTP has trippedShutdown vs Protection Alarm Clear Protection EventTo recall settings To store save settingsTo save default settings To power on user setting #1 To reset the unit To change the power on at output stateFeature Reset State *RST Configure To read from the error queueAuxiliary To set up Auxiliary line B To set up Auxiliary line aTo check the state of the line Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command To set the current limits To set the voltage limitsTriggered To set a triggered setpoint To program triggers Operation Option Identification Query Identification QueryStatus Registers RegisterStatus Registers Operation Status Registers Bit Bit Bit Weight Bit Name DescriptionBit Name Description Sub-Register Bit Bit Weight Bit Name Description Protection SHUTdownSHare CurrentSub-Register Questionable Status Registers Sub-Register Table TimeSummarizes the standard Event Status Register Been lost. See Query Error List on QSR Service MasterSummary RequestCommands Status Register CommandsRegister Filter/Enable Preset Value Ieee Status Event Commands Scpi equivalent for multichannel useSTB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? STATchannelOPERCSHEVEN? QuestionableCommands STATchannelQUESVOLTCOND? Current Sharing No sharing Current SharingOperation Current Sharing Service Request and Polling Codes and StandardsMessage Terminators Address RangeControl Functions Protocol SpecificationsFunction Mnemonic Description Functions Subset Electrical Specifications Mechanical SpecificationsPerformance Specifications Signal Driver LinePerformance Specifications Appendix B. Scpi Command Reference Scpi Command Reference IEEE-488.2/SCPI Syntax and StyleUnderstanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Scpi Command Summary NotationsTables UsedTable B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 Table B.12User Lines 112Table B.14Auto Sequence Commands StepnumberDELete Expressions Expression DetailsExpressions Appendix C. Error Messages Command Error List Execution Error ListError Messages Errorcode Error Message DescriptionExecution Error List Device-Specific Error List Error Error Message Description CodeUser Request Event Query Error ListOperation Complete Event Front Panel Error Codes CPU Error CodesAnalog Programming Interface Error codes Auto Sequencing Error CodesCANbus Error Codes Multichannel Error CodesCurrent Share Error Codes Entering Calibration Mode Appendix D. CalibrationSetup and Equipment CalibrationCalibration Procedure Output VoltageEnter current data Exit calibration mode Restore Factory CalibrationRestore Factory Calibration Page Xantrex Technology Inc