Front Panel Error Codes | Xantrex Technology GPIB-M-XFR3, GPIB-M-XT

Error Messages

Front Panel Error Codes

Front Panel Error Codes

Table C.7 Front Panel Error Codes

	Error	Error Message Description
	code	Error Message Description
	code
	+1301	Front Panel Protocol Error
		Invalid data from the front panel was sent to the CPU

	+1302	Front Panel Not Responding

	+1303	Front Panel Self-Test Failed

CPU Error Codes

Table C.8 CPU Error Codes

	Error	Error Message Description
	code	Error Message Description
	code
	+1401 ColdFire Self-Test Failed

Analog Programming Interface Error codes

Table C.9 Analog Programming Interface Error code

	Error	Error Message Description
	code	Error Message Description
	code

+1501 Analog programming self-test failed

Auto Sequencing Error Codes

Table C.10Auto Sequencing Error Codes

	Error	Error Message Description
	code	Error Message Description
	code
	+1601 Invalid step number
		Step does not exist, is out of allowed range or preceding steps do not exist.

122	Operating Manual for Multichannel Functionality (GPIB-M)

Image 124

Xantrex Technology GPIB-M-XFR3 manual Front Panel Error Codes, CPU Error Codes, Analog Programming Interface Error codes

Contents

Operating Manual Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase Date Safety Supply Describes the power supply and lists Its features and specificationsGives basic setup procedures Installation and Configuration Manual Revisions Power Supply Safety MarkingsAbout This Manual Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Features and Functions Description Functions Features and SpecificationsReadback Specifications Models 15-20 30-10 60-5 Models 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Models 18-30 33-16 60-9 120-4.5 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Features and Specifications Introduction Initial Inspection XFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface To install the ferrite block Basic Setup ProcedureIEEE-488 Controller Connection Configure power supply Power on Power on the unit Configure Computer ControllerTest Feature Factory Preset Value Configure for Gpib Operation Change Remote Control Source Configure for Multichannel Operation Example CANbus CablesCAN-only Interface Operation UsingMultichannel Appendix B. Scpi Command Reference lists all commands Specifications User Lines Pin # Function Input/Output User Lines Connection XT, HPD XPD 13Schematic For User Line Interface Powering on Supply Overview Power Supply Operating States Operation Power Supply Regulation Modes Remote Control Modes Front Panel LEDs Description Power Supply Operation To query to remote modeMode Changing the remote/local state To enable or disable the output To query the state of the output enable MEASVOLT? MEASCURR? Configure Output Protection To set the fold mode To set the fold delay Set Shutdown Recovery for AC Off Additional ProtectionsTo query if AC Off has tripped To query if OTP has tripped Shutdown vs Protection Alarm Clear Protection Event To recall settings To store save settingsTo save default settings To power on user setting #1 To reset the unit To change the power on at output stateFeature Reset State *RST Configure To read from the error queueAuxiliary To set up Auxiliary line B To set up Auxiliary line aTo check the state of the line Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command To set the current limits To set the voltage limitsTriggered To set a triggered setpoint To program triggers Operation Option Identification Query Identification Query Status Registers Register Status Registers Operation Status Registers Bit Bit Bit Weight Bit Name DescriptionBit Name Description Sub-Register Bit Bit Weight Bit Name Description Protection SHUTdown SHare CurrentSub-Register Questionable Status Registers Sub-Register Table Time Summarizes the standard Event Status Register Been lost. See Query Error List on QSR Service MasterSummary Request Commands Status Register CommandsRegister Filter/Enable Preset Value Ieee Status Event Commands Scpi equivalent for multichannel use STB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? STATchannelOPERCSHEVEN? Questionable Commands STATchannelQUESVOLTCOND? Current Sharing No sharing Current Sharing Operation Current Sharing Service Request and Polling Codes and StandardsMessage Terminators Address Range Control Functions Protocol SpecificationsFunction Mnemonic Description Functions Subset Electrical Specifications Mechanical SpecificationsPerformance Specifications Signal Driver Line Performance Specifications Appendix B. Scpi Command Reference Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Understanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Scpi Command Summary NotationsTables Used Table B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 Table B.12User Lines 112 Table B.14Auto Sequence Commands StepnumberDELete Expressions Expression Details Expressions Appendix C. Error Messages Command Error List Execution Error ListError Messages Errorcode Error Message Description Execution Error List Device-Specific Error List Error Error Message Description Code User Request Event Query Error ListOperation Complete Event Front Panel Error Codes CPU Error CodesAnalog Programming Interface Error codes Auto Sequencing Error Codes CANbus Error Codes Multichannel Error Codes Current Share Error Codes Entering Calibration Mode Appendix D. Calibration Setup and Equipment Calibration Calibration Procedure Output Voltage Enter current data Exit calibration mode Restore Factory Calibration Restore Factory Calibration Page Xantrex Technology Inc