Master, Summary, Request, Service | Xantrex Technology GPIB-M-XFR3

Status Registers

Overview

Master	The Master Summary Status message indicates that the power supply has at least one
Summary	reason for requesting service. Although the MSS message is sent in bit position 5 of
Status (MSS)	the response to *STB?, it is not sent in response to a serial poll and not considered
	part of the Status Byte.
	MSS is TRUE if:
	• Status Byte bit 0 AND Service Request Enable Register bit 0, or
	• Status Byte bit 1 AND Service Request Enable Register bit 1, or
	• Status Byte bit 2 AND Service Request Enable Register bit 2, or
	• Status Byte bit 3 AND Service Request Enable Register bit 3, or
	• Status Byte bit 4 AND Service Request Enable Register bit 4, or
	• Status Byte bit 5 AND Service Request Enable Register bit 5, or
	• Status Byte bit 7 AND Service Request Enable Register bit 7.
Request	RQS is TRUE if the Service Request Enable Register has a bit set and there is a
Service	corresponding bit within the Status Byte.
(RQS)	The SRQ line of the GPIB will be set. The SRQ annuciator will be lit.

80	Operating Manual for Multichannel Functionality (GPIB-M)

Image 82

Xantrex Technology GPIB-M-XFR3, GPIB-M-XHR, GPIB-M-XT, GPIB-M-XPD, GPIB-M-HPD manual Master, Summary, Request, Service

Contents

Operating Manual Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase Date Safety Supply Gives basic setup procedures Describes the power supply and listsIts features and specifications Installation and Configuration Manual Revisions Power Supply Safety MarkingsAbout This Manual Table of Contents Status Registers Current Sharing Appendix B. Scpi Command Reference List of Tables List of Tables List of Figures List of Figures Features and Functions Description Functions Features and SpecificationsReadback Specifications Models 15-20 30-10 60-5 Models 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Models 18-30 33-16 60-9 120-4.5 Models 15-4 20-3 30-2 60-1 120-0.5 250-0.25 Features and Specifications Introduction Initial Inspection XFR 1200 Watt model shown XT and HPD Power Supply Front Panel with Gpib Interface XFR 2800 Watt Power Supply Rear Panel with GPIB-M Interface XHR Power Supply Rear Panel with GPIB-M Interface XT/HPD Power Supply Rear Panel with GPIB-M Interface To install the ferrite block Basic Setup ProcedureIEEE-488 Controller Connection Configure power supply Power on Power on the unit Configure Computer ControllerTest Feature Factory Preset Value Configure for Gpib Operation Change Remote Control Source Configure for Multichannel Operation Example CAN-only CANbusCables Interface Operation UsingMultichannel Appendix B. Scpi Command Reference lists all commands Specifications User Lines Pin # Function Input/Output User Lines Connection XT, HPD XPD 13Schematic For User Line Interface Powering on Supply Overview Power Supply Operating States Operation Power Supply Regulation Modes Remote Control Modes Front Panel LEDs Description Mode Power Supply OperationTo query to remote mode Changing the remote/local state To enable or disable the output To query the state of the output enable MEASVOLT? MEASCURR? Configure Output Protection To set the fold mode To set the fold delay To query if AC Off has tripped Set Shutdown Recovery for AC OffAdditional Protections To query if OTP has tripped Shutdown vs Protection Alarm Clear Protection Event To recall settings To store save settingsTo save default settings To power on user setting #1 To reset the unit To change the power on at output stateFeature Reset State *RST Configure To read from the error queueAuxiliary To set up Auxiliary line B To set up Auxiliary line aTo check the state of the line Auto Sequencing PROGSTEPstepnumberEDIT voltage Current,OVPlevel,timeTRIG To delete any step from the sequence You can also use the following to delete all sequences To run, stop or pause a sequence, use the following command To set the current limits To set the voltage limitsTriggered To set a triggered setpoint To program triggers Operation Option Identification Query Identification Query Status Registers Register Status Registers Operation Status Registers Bit Bit Bit Weight Bit Name DescriptionBit Name Description Sub-Register Bit Bit Weight Bit Name Description Protection SHUTdown SHare CurrentSub-Register Questionable Status Registers Sub-Register Table Time Summarizes the standard Event Status Register Been lost. See Query Error List on QSR Summary ServiceMaster Request Commands Status Register CommandsRegister Filter/Enable Preset Value Ieee Status Event Commands Scpi equivalent for multichannel use STB? Or the multichannel equivalent STATuschannelSBYTeEVENt? Sub-Register STATchannelOPERSHUTEVEN? STATchannelOPERCSHEVEN? Questionable Commands STATchannelQUESVOLTCOND? Current Sharing No sharing Current Sharing Operation Current Sharing Message Terminators Service Request and PollingCodes and Standards Address Range Control Functions Protocol SpecificationsFunction Mnemonic Description Functions Subset Performance Specifications Electrical SpecificationsMechanical Specifications Signal Driver Line Performance Specifications Appendix B. Scpi Command Reference Scpi Command Reference IEEE-488.2/SCPI Syntax and Style Understanding Scpi Commands Is the same as typing Using Queries Boolean Parameters Tables Scpi Command SummaryNotations Used Table B.1IEEE 488.2 Commands Table B.2Readback Commands Table B.3Commands for Output Control Table B.4Commands for Current Share Table B.7Commands for Fold Protection Table B.10Status Commands STATuschannelOPERationREGulatingCONDition? 111 Table B.12User Lines 112 Table B.14Auto Sequence Commands StepnumberDELete Expressions Expression Details Expressions Appendix C. Error Messages Error Messages Command Error ListExecution Error List Errorcode Error Message Description Execution Error List Device-Specific Error List Error Error Message Description Code User Request Event Query Error ListOperation Complete Event Analog Programming Interface Error codes Front Panel Error CodesCPU Error Codes Auto Sequencing Error Codes CANbus Error Codes Multichannel Error Codes Current Share Error Codes Entering Calibration Mode Appendix D. Calibration Setup and Equipment Calibration Calibration Procedure Output Voltage Enter current data Exit calibration mode Restore Factory Calibration Restore Factory Calibration Page Xantrex Technology Inc