2. Song Recording
186 RS7000
SWING
OFF when VALUE = OFF
50% ~ 75% when VALUE =
60 , 120 , 240 , 480
66% ~ 83% when VALUE =
80 , 160 , 320
Record quantize aligns the timing of notes which are not
exactly on the beat on-the-fly as you record.
The record quantize parameters can be set in the Rec Standby
mode when the REPLACE or OVERDUB record type is
selected.
The quantize VALUE parameter specifies the note timing to
which the nearest recorded notes will be aligned.
The quantize SWING parameter specifies by how much the
timing of notes on even-numbered beats (back beats) will be
delayed to create a swing feel.
When a triplet VALUE is specified, the last note of each trip-
let is affected by the SWING parameter.
To adjust the SWING parameter, press [F3] to move the cursor to
SWING, then use [Knob 3] to adjust.
4BPM (Tempo)
....[Knob 4], [F4] → [Knob 4], [SHIFT]+[F4] → Numeric Keypad
This parameter has the same effect as in the SONG Play mode.
See page 183 for details.
5Punch-in Point, Punch-out Point
....[Knob 3], [F3] → [Knob 3], [SHIFT]+[F3] → Numeric Keypad
Can be set when the REC TYPE is set to PUNCH.
[Settings]
IN.......................001:1 ~ 999:4
OUT...................001:1 ~ 999:4
Set the punch-in and punch-out points for PUNCH real-time
recording.
Use [F3] to move the cursor to IN or OUT, and [Knob 3] to
set these values as required.
For example, first use [Knob 3] to enter the IN measure, then
press [F3] to move the cursor and use [Knob 3] to set the
OUT measure. [F3] can then be used to move the cursor to
the IN beat and OUT beat parameters, which can also be set
as required by using [Knob 3].
6EVENT TYPE
..........................[Knob 3], [SHIFT]+[F3] → Numeric Keypad
When the STEP record type is selected this parameter specifies
the type of event to be recorded.
[Settings] NOTE, PITCH BEND,
CC[000] ~ CC[119] (Control Change),
BPM Change
(when the BPM track is selected)
NOTE............................. note data is recorded.
PITCH BEND................. pitch bend change data is
recorded.
CC[000] ~ CC[119]........ the corresponding control
change data is recorded: vol-
ume, pan, expression, etc.
BPM............................... tempo change data is
recorded.
Specifies the type of data to be recorded.
Numeric key input is valid only when inputting control
change numbers.
Real-time recording allows anything played on the RS7000 key-
board, operation of the assignable knobs, and data received from
an external MIDI controller to be recorded in real time.
In this section we’ll look at the real-time REPLACE, OVER-
DUB, and PUNCH recording procedure.

Record Procedure (REPLACE, OVERDUB)

1. Press [SONG] to enter the SONG Play mode.
2. Use [Knob 1] (SONG) to select the song to be recorded.
3. Press [REC] to engage the Rec Standby mode.
4. Use [Knob 1] (REC TRACK) to select the record track.
5. Press [MIXER] to access the Voice Select display and use
[Knob 1] (BANK) and [Knob 3] (PROGRAM) to select the
desired voice, then press [EXIT] to return to the Rec Standby
display.
6. Use [Knob 2] (REC TYPE) to select the REPLACE or OVER-
DUB record type.
Also use [Knob 3] and [F3] to set up record quantize, and
[Knob 4] to set the BPM as required.
NOTE
•When the OVERDUB record type is selected,
quantization will also be applied to the exist-
ing data in the track.
•When record quantize is not OFF, quantiza-
tion is applied to all controller data in addition
to the note data. Use the Quantize job to
quantize only the note data.
Back beat
Original timing
Quantize value
(Swing rate = 50%)
Quantize value
(Swing rate = 60%)
Back beat
Quarter note
length
Real-Time Recording