Yamaha RS7000 - page 268

2. MIDI Events Handled by the RS7000

268 RS7000

●Effect Send Level 1 (Reverb Effect)

(Control Number 091)

• Speciﬁes the reverb effect send level.

●Effect Send Level 3 (Chorus Effect)

(Control Number 093)

• Speciﬁes the delay/chorus effect send level.

●Effect Send Level 4 (Variation Effect)

(Control Number 094)

• Speciﬁes the variation effect send level.

●Data Increment (Control Number 096)

●Data Decrement (Control Number 097)

• These MIDI messages increment or decrement by one the

value of pitch bend sensitivity, ﬁne tune, or coarse tune settings

made using RPN (Page 269).

●NRPN MSB (Non-Registered Parameter Number

MSB) (Control Number 099)

●NRPN LSB (Non-Registered Parameter Number

LSB) (Control Number 098)

• Used primarily as offset values for vibrato, ﬁlter, EG, drum

setup and other settings.

• Data Entry (Page 267) is used to set the parameter value after

specifying the parameter using the NRPN MSB and LSB.

• Once an NRPN is speciﬁed, the following data entry message

received on the same channel is processed as the value of that

NRPN. Prevent operational errors by transmitting an RPN Null

message (7FH, 7FH) after using these messages to perform a

control operation.

• Refer to “8. NRPN” for information about the parameter. (Page

270)

●RPN MSB (Registered Parameter Number MSB)

(Control Number 101)

●RPN LSB (Registered Parameter Number LSB)

(Control Number 100)

• Used primarily as offset values for pitch bend sensitivity, tun-

ing, and other part settings.

• Data Entry (Page 267) is used to set the parameter value after

specifying the parameter using the RPN MSB and RPN LSB.

• Once an RPN is speciﬁed, the following data entry message

received on the same channel is processed as the value of that

RPN. Prevent operational errors by transmitting an Null mes-

sage (7FH, 7FH) after using these messages to perform a con-

trol operation.

• Refer to “7. RPN” for information about the parameter. (Page

269)

●All Sound Off (Control Number 120)

• Turns all currently sounding notes off for all parts.

●Reset All Controllers (Control Number 121)

• Resets all controllers to their initial values. The following

parameters are affected: Pitch Bend, Channel Pressure, Poly-

phonic Key Pressure, Modulation, Expression, Hold 1, Porta-

mento, Sostenuto, Soft Pedal, Portamento Control, RPN*,

NRPN* (* The RPN and NRPN are speciﬁed as having no

number, and no internal data is changed).

• The following data is not affected: Program Change, Bank

Select MSB and LSB, Volume, Pan, Dry Send Level, Effect

Send Level 1, 3, and 4, Pitch Sensitivity, Fine Tuning, Coarse

Tuning.

●Omni Mode Off (Control Number 124)

• Performs the same operation as when an All Notes Off message

is received. The voice receive channel is set to 1.

●Omni Mode On (Control Number 125)

• Performs the same operation as when an All Notes Off message

is received. Only the voice receive channel is set to Omni On.

●Mono (Control Number 126)

• Performs the same operation as when an All Sound Off mes-

sage is received. If the 3rdbyte parameter (the parameter that

determines the mono number) is 0 ~ 16 the parts corresponding

to those channels are set to mono.

●Poly (Control Number 127)

�� Performs the same operation as when an All Sound Off mes-

sage is received, and sets the parts corresponding to those

channels are set to poly.