|
|
| TROUBLESHOOTING | EN 37 | |
|
|
|
| ||
|
|
|
|
| |
Picture does not appear on the LCD |
|
| TAPE! |
| |
monitor. |
|
| Appears if a tape is not loaded when the | ||
● The viewfinder is pulled out and “PRIORITY” is |
| Recording Start/Stop Button or SNAPSHOT | |||
set to “FINDER”. |
| Button is pressed while the Power Switch is set | |||
➜Push the viewfinder back in or set “PRIORITY” to |
| to “REC”. | |||
“LCD”. ( pg. 18, 22, 24) |
|
|
|
| |
● The LCD monitor’s brightness setting is too dark. |
| TAPE END |
| ||
➜Adjust the brightness of the LCD monitor. |
| Appears when the tape ends during recording or | |||
( pg. 15) |
| ||||
| playback. | ||||
➜If the monitor is tilted upward 180 degrees, open |
| ||||
|
|
|
| ||
the monitor fully. ( pg. 18) |
|
|
|
| |
| SET DATE/TIME! |
| |||
|
|
|
| ||
An error indication (01 – 04 or 06) appears. |
|
| ÷Appears when the date/time is not set. | ||
● A malfunction of some kind has occurred. In this |
| ( pg. 14) | |||
case the camcorder’s functions become |
| ÷The | |||
unusable. |
| previously set date/time has been erased. | |||
➜ pg. 37. |
| Consult your nearest JVC dealer for | |||
Warning Indications |
| replacement. | |||
|
|
|
| ||
| LENS CAP |
| |||
|
|
|
| ||
|
| ||||
|
|
|
|
|
|
Displays the battery remaining power.
Remaining power level
|
|
|
|
|
|
|
|
|
|
|
|
|
|
High |
|
|
|
| Exhausted | |
As the battery power comes close to nil, the battery remaining power indicator blinks. When the battery power is exhausted, power turns off automatically.
●Appears if a tape is loaded. ( pg. 16)
●Blinks when no tape is loaded. ( pg. 16)
CHECK TAPE’S ERASE PROTECTION TAB
Appears when the erase protection tab is set to “SAVE” while the Power Switch is set to “REC”. ( pg. 13)
USE CLEANING CASSETTE
Appears if dirt is detected on the heads during recording. Use an optional cleaning cassette. ( pg. 40)
CONDENSATION, OPERATION
PAUSED PLEASE WAIT
Appears if condensation occurs. When this indication is displayed, wait more than 1 hour until condensation disappears.
Appears for 5 seconds after power is turned on if the lens cap is attached or when it is dark.
HDV 
Appears when pictures recorded in the HDV format are detected. The pictures in the HDV format cannot be played back with this camcorder.
UNIT IN SAFEGUARD MODE REMOVE AND REATTACH BATTERY OR DC PLUG
The error indications (01, 02 or 06) show what type of malfunction has occurred. When an error indication appears, the camcorder turns off automatically. Remove the power supply (battery, etc.) and wait a few minutes for the indication to clear. When it does, you can resume using the camcorder. If the indication remains, consult your nearest JVC dealer.
UNIT IN SAFEGUARD MODE
EJECT AND REINSERT TAPE
The error indications (03 or 04) show what type of malfunction has occurred. When an error indication appears, the camcorder turns off automatically. Eject the cassette once and re- insert it, then check if the indication clears. When it does, you can resume using the camcorder. If the indication remains, consult your nearest JVC dealer.