Agilent Technologies 33120A manual Waveforms

Chapter 1 Specifications

Agilent 33120A Function Generator

WAVEFORMS

Standard Waveforms:	Sine, Square, Triangle,
	Ramp, Noise, DC volts,
	Sine(x)/x, Negative Ramp,
	Exponential Rise,
	Exponential Fall, Cardiac
Arbitrary Waveforms:
Waveform Length:	8 to 16,000 points
Amplitude Resolution:	12 bits (including sign)
Sample Rate:	40 MSa / sec
Non-Volatile Memory:	Four 16,000-point waveforms

FREQUENCY CHARACTERISTICS

Sine:	100	Hz –	15 MHz
Square:	100	Hz –	15 MHz
Triangle:	100	Hz –	100 kHz
Ramp:	100	Hz –	100 kHz
Noise (Gaussian):	10 MHz bandwidth
Arbitrary Waveforms:	100	Hz –	5 MHz
8 to 8,192 points:
8,193 to 12,287 points:	100	Hz –	2.5 MHz
12,288 to 16,000 points:	100 ￿Hz –		200 kHz
Resolution:	10 ￿Hz or		10 digits
Accuracy:	10 ppm in 90 days,
	20 ppm in 1 year,
	18￿C – 28 C
Temperature Coefficient:	< 2 ppm / ￿C
Aging:	< 10 ppm / yr
SINEWAVE SPECTRAL PURITY (into 50￿)
Harmonic Distortion
DC to 20 kHz:	-70 dBc
20 kHz to 100 kHz:	-60 dBc
100 kHz to 1 MHz:	-45 dBc
1 MHz to 15 MHz:	-35 dBc
Total Harmonic Distortion
DC to 20 kHz:	< 0.04%
Spurious (non-harmonic)
Output (DC to 1 MHz):	< -65 dBc
Output (> 1 MHz):	< -65 dBc + 6 dB/octave
Phase Noise:	< -55 dBc in a 30 kHz band

SIGNAL CHARACTERISTICS

Squarewave
Rise/Fall Time:	< 20 ns
Overshoot:	< 4%
Asymmetry:	1% + 5 ns
Duty Cycle:	20% to 80% (to 5 MHz)
	40% to 60% (to 15 MHz)
Triangle, Ramp, Arb
Rise/Fall Time:	40 ns (typical)
Linearity:	< 0.1% of peak output
Settling Time:	< 250 ns to 0.5% of final value
Jitter:	< 25 ns

OUTPUT CHARACTERISTICS (1)

Amplitude (into 50￿): (2)	50 mVpp – 10 Vpp
Accuracy (at 1 kHz):	1% of specified output
Flatness	(sine wave relative to 1 kHz)
< 100 kHz:	1% (0.1 dB)
100 kHz to 1 MHz:	1.5% (0.15 dB)
1 MHz to 15 MHz:	2% (0.2 dB) Ampl ￿3Vrms
1 MHz to 15 MHz:	3.5% (0.3 dB) Ampl < 3Vrms
Offset (into 50￿): (3)	￿￿5 Vpk ac + dc
Accuracy: (4)	2% of setting + 2 mV
Output Impedance:	50 ohms fixed
Resolution:	3 digits, Amplitude and Offset
Output Units:	Vpp, Vrms, dBm
Isolation:	42 Vpk maximum to earth
Protection:	Short￿￿-circuit protected
	15 Vpk overdrive < 1 minute

(1)Add 1/10th of output amplitude and offset specification per ￿C for operation outside of 18￿C to 28￿C range (1-year specification).

(2)100 mVpp – 20 Vpp amplitude into open-circuit load.

(3)Offset ￿￿2 X peak-to-peak amplitude.

(4)For square wave outputs, add 2% of output amplitude additional error.

14