Manuals / Agilent Technologies / Power Tools / Welding System

Agilent Technologies 33120A manual Front-Panel Menu at a Glance, MODulation Menu

Models: 33120A

1 146

Download 146 pages 51 Kb

Page 6

The Front-Panel Menu at a Glance

The menu is organized in a top-down tree structure with three levels.

A:MODulation MENU

1:AM SHAPE 2: AM SOURCE 3: FM SHAPE 4: BURST CNT 5: BURST RATE

6: BURST PHAS 7: BURST SRC 8: FSK FREQ 9: FSK RATE 10: FSK SRC

B:SWP (Sweep) MENU

1:START F 2: STOP F 3: SWP TIME 4: SWP MODE

C:EDIT MENU*

1: NEW ARB [ 2: POINTS ] [ 3: LINE EDIT ] [ 4: POINT EDIT ] [ 5: INVERT ] [ 6: SAVE AS ] 7: DELETE

*The commands enclosed in square brackets ( [ ] ) are “hidden” until you make a selection from the NEW ARB command to initiate a new edit session.

D:SYStem MENU

1:OUT TERM 2: POWER ON 3: ERROR 4: TEST 5: COMMA 6: REVISION

E:Input / Output MENU

1:HPIB ADDR 2: INTERFACE 3: BAUD RATE 4: PARITY 5: LANGUAGE

F:CALibration MENU*

1: SECURED or [ 1: UNSECURED ] [ 2: CALIBRATE ] 3: CAL COUNT 4: MESSAGE

*The commands enclosed in square brackets ( [ ] ) are “hidden” unless the function generator is UNSECURED for calibration.

4

Image 6

Agilent Technologies 33120A manual Front-Panel Menu at a Glance, MODulation Menu

Contents

Service Guide Agilent 33120A MHz Function Arbitrary Waveform GeneratorPage Convenient bench-top features Flexible system featuresFront Panel at a Glance Front-Panel Number Entry Front-Panel Menu at a Glance MODulation MenuDisplay Annunciators TrigRear Panel at a Glance Use the front-panel Input / Output Menu toThis Book Page Contents Contents Service SchematicsReplaceable Parts Contents Specifications Waveforms Modulation Characteristics General Specifications Product Dimensions Page Quick Start Quick Start To prepare the function generator for use One User’s Guide 〈 This Service GuideConnect the power cord and turn on the function generator Check the list of supplied itemsVerify that the power-line fuse is good Verify that there is ac power to the function generatorVerify the power-line voltage setting If the function generator does not turn onRemove the power cord . Remove To adjust the carrying handle Enter the magnitude of the desired frequency To cancel the number mode, press Shift CancelTo set the output frequency Set the units to the desired valueTo set the output amplitude Enter the magnitude of the desired amplitudeTo set a dc offset voltage How to change the offset to -1.5 mVdcEnable the offset modify mode Enter the magnitude of the desired offsetEnter the desired duty cycle To set the duty cycleSelect the square wave function Output the waveform with the displayed duty cycleMove across to the Exprise choice To output a stored arbitrary waveformDisplay the list of arbitrary waveforms Select and output the displayed arbitrary waveformTo output a dc voltage Enter the magnitude of the desired voltageTo store the instrument state Set up the function generator to the desired configurationTurn on the state storage mode Save the instrument stateRestore the instrument state Recall the stored instrument stateTo rack mount the function generator Quick Start Front-Panel Menu Operation Front-Panel Menu Operation Front-panel menu reference MODulation MenuFront-panel menu reference SYStem Menu Front-panel menu tutorial Messages Displayed During Menu Use Move across to the Power on command on this level Turn on the menuMove across to the SYS Menu choice on this level Cycle the power to restore the default values Move down a level to the Parameter choicesSave the change and turn off the menu Select amplitude adjustment Increment the first digit until 300.0 mVPP is displayedMove down a level to the OUT Term command To select the output terminationMove down a level and then across to the High Z choice To output a modulated waveform Select AMUse the menu to select the shape of the modulating waveform Move down a level verify that Sine is selected Set the modulating frequency to 200 HzSet the modulation depth to 80% Move down a level to the Secured command To unsecure the function generator for calibrationMove across to the CAL Menu choice on this level Move down to the parameters level Calibration Procedures Calibration Procedures Agilent Calibration Services Calibration IntervalTime Required for Calibration Automating Calibration Procedures Recommended Test EquipmentTest Considerations Performance Verification Tests Self-TestQuick Performance Check Frequency Verification Function Gain and Linearity VerificationDC Function Offset Verification AC Amplitude VerificationAC Amplitude Verification Vrms 0.00035 Vrms Amplitude Flatness Verification 15.00 MHzAM Modulation Depth Verification Vrms 0.0061 VrmsOptional Performance Verification Tests Square Wave Duty Cycle VerificationDistortion Verification Calibration Security Code CharactersTo Unsecure the Function Generator Without the Security Code Calibration Count Calibration MessageBegin the Frequency and Burst Rate adjustment procedure General Calibration/Adjustment ProcedureMove down a level to the Unsecured command Move across to the Calibrate choicePerform the next adjustment procedure Calculate and save the new valueFrequency and Burst Rate Adjustment Aborting a Calibration in ProgressFunction Gain and Linearity Adjustment AC Amplitude Adjustment High-ZAC Amplitude Adjustment High-Z Modulation Adjustment Frequency AmplitudeAC Amplitude Adjustment 50W AC Amplitude Adjustment 50W Adjustment for KHz DC Output Adjustment SetupDuty Cycle Adjustment AC Amplitude Flatness AdjustmentAC Amplitude Flatness Adjustment Exiting Output Amplifier Adjustment Optional Error Messages System Error MessagesSelf-Test Error Messages Calibration Error Messages Theory of Operation Self-test procedures are described in chapter Theory of OperationBlock Diagram Overview This discussion pertains to the block diagram shown onBlock 8 on block diagram page 129 Schematic on Output AttenuatorBlock 7 on block diagram page 129 Schematic on Output Amplifier740 R710 R717 740 R710 R711 R715 R716 R719 R720 AM Modulation Pre-attenuator Block 6 on block diagram page 129 Schematic onBlock 6 on block diagram page 129, schematic on Square Wave and SyncSquare Wave and Sync Block 5 on block diagram page 129 Schematic on FiltersBlock 4 on block diagram page 129 Schematic on Waveform DAC/Amplitude Leveling/Waveform RAMWaveform DAC/Amplitude Leveling/Waveform RAM Block 2 on block diagram page 129 Schematic on Direct Digital Synthesis DDS AsicBlock 3 on block diagram page 129 Schematic on System DACsBlock 1 on block diagram page 129 Schematic on Floating LogicBlock 10 on block diagram page 129 Schematic on Power SuppliesBlock 9 on block diagram page 129 Schematic on Earth-Referenced LogicPower Supplies Block 11 on block diagram page 129 Schematic on Display and KeyboardSee Service Service See To prepare the function generator for use on Operating ChecklistIs the function generator inoperative? Does the function generator fail self-test?Types of Service Available Call 1-877-447-7278 and ask for Agilent ExpressCleaning Repackaging for ShipmentAgilent suggests that you always insure shipments Electrostatic Discharge ESD Precautions Surface Mount RepairTo Replace the Power-Line Fuse To Replace the Output Protection Fuse F801Unit is Inoperative Troubleshooting HintsUnit Reports Error Unit Fails Self-TestPower Supply Problems Self-Test Procedures Power-On Self-Test625 112 Replaceable Parts Replaceable Parts Main PC Assembly 116 117 118 119 120 121 122 123 Display and Keyboard PC Assembly 33120A Mainframe Manufacturer’s List Schematics8 Schematics Block Diagram Pull Off Handle Loosen Captive Sheet 1 132 Sheet 3 Sheet 4 Waveform DAC Schematic 134 Sheet 5 136 Sheet 7 Sheet 8 Output Attenuator Schematic 138 Sheet 9 of 10 Earth Reference Logic Schematic Sheet 10 Power Supplies Schematic 140 Sheet 1 of 1 Display and Keyboard Schematic TOP Side 33120-66521 REV a TOP Side 33120-66502 REV C Manual Part Number