Stepperb, Gpioa, Gpiob, Ssram, Vic, Can | Arm Enterprises IM-AD1

Reference Design Example

Table 4-3 Integrator/IM-AD1 memory map (continued)

Device	Address

STEPPERB	0xC0C00000

GPIOA	0xC0D00000

GPIOB	0xC0E00000

Reserved	0xC1000000

SSRAM	0xC2000000

VIC	0xC3000000

CAN	0xC4000000

ADC/DAC	0xC5000000

PIB	0xCFFFFF00

ARM DUI 0163B

Copyright © 2001-2003. All rights reserved.

4-7

Image 53

Arm Enterprises IM-AD1 manual Stepperb, Gpioa, Gpiob, Ssram, Vic, Can, Adc/Dac, Pib

Contents

Integrator/IM-AD1 User Guide Integrator/IM-AD1 Conformance Notices Copyright 2001-2003. All rights reserved Chapter Introduction Integrator/IM-AD1 User Guide Appendix a Signal Descriptions Preface Intended audience Using this bookAbout this book ARM publications Typographical conventionsFurther reading Third-party documents Feedback on the Integrator/IM-AD1 FeedbackFeedback on this document Xii Introduction ARM DUI 0163B About the Integrator/IM-AD1 Integrator/IM-AD1 layout Features Interface module features and architecture Architecture Integrator/IM-AD1 block diagram Links and LEDs Config LED Care of modules Introduction Copyright 2001-2003. All rights reserved Getting Started Assembled Integrator development system Fitting the interface module Switch 2 Closed Switch 3 Open Switch 4 Open Setting up the logic module Running the test software Hardware Reference Hardware Reference Connector Serial interface signal assignment Signal nameUart interface Description Serial connector signal assignment Pin J18 Type Description Serial connector pinout SPI SPI signals Signal PWM interface PWM interface signals Signal PWM connector signals Pin J14 J10 Description Shows the signal assignment Functional description Stepper motor interface Therefore, with a 0.1Ω sense resistor fitted Stepper motor interface signal summary Stepper motor interface signals Stepper motor connectors VSS Stepper motor connector signals Pin J19 J23 Description Gpio Gpio connectors J16 and J17 Hardware Reference Buffer Can interfaceU13 Can interface signal assignment Signal IMBBANK30 IMBBANK28IMBBANK29 GND Can connector signal assignments Pin 10 ADC and DAC interface architecture ADC and DAC interfaces IMABANK49 IMABANK48IMABANK50 IMABANK51 11shows the pinout of the ADC interface connector J1 12 shows the pinout of the DAC interface connector J2 Hardware Reference Copyright 2001-2003. All rights reserved Reference Design Example Example architecture About the design exampleAbout PrimeCells File Description Vhdl file descriptions Example memory map Integrator system memory map Address assignment of logic modules Integrator/IM-AD1 memory map Device Address Integrator/IM-AD1 memory mapLogic module addresses Position Bits Stack Gpioa StepperbGpiob Ssram Offset address Name Type Function Example APB register peripheralLogic module registers Oscillator divisor registers VDW LMOSCx registers Bits Name Access FunctionRDW Oscillator lock register Bits Name Access FunctionUser LEDs control register Push button interrupt register Switches register Uart SPICS2 SPI chip select registerSPICS1 SPICS0 Synchronous serial port PWM controller Stepper motor peripheral Offset Name Access Function AddressCont Count Stepper x control register DIR DocountSinglestep Stepx speed register Stepx count register Address offset Name Access Size Function Read data output pinsData output set register Read data input register Gpio direction control 1 bit Data direction Ssram interface Interrupt sources Vectored interrupt controllerInterrupt Interrupt source Source number CAN1 Reference Design Example Canreset Can reset control registerCan controller interface CANxBase 16 ADC and DAC interface registers ADC and DAC interfaceAdcstatus ADC2BUSY Bits Name Function Peripheral information block18 PIB entry format Signal Descriptions Expa Pin label Signal Description Table A-1 AHB signal assignment Expb Pin label Name Description Table A-2 Expb signal description Expim LM-EP20K1000E Description Table A-3 Expim signal descriptionsLabel Figure A-4 J7 pin locations Logic analyzer connector CLK1 Table A-4 J7 connector pinout Signal Pin Multi-ICE Jtag Figure A-5 Multi-ICE connector pinout Mechanical Specification Mechanical information Figure B-1 Board dimensions top view Figure B-2 Bottom board dimensions viewed from top side DB9STRAIGHT FCI Connector referenceDB9DUAL Multi-ICE Glossary Synchronous Serial Port ADC Can IndexDAC Gpio Lmleds Lmlock LMOSC1 Expa A-2Gpiodataclr Gpiodatain Gpiodataout Gpiodataset Gpiodirn