Mechanical Specification | Arm Enterprises IM-AD1 manual

Appendix B

Mechanical Specification

This appendix contains the mechanical specification for Integrator/IM-AD1. It contains the following section:

•Mechanical information on page B-2

•Connector reference on page B-4.

ARM DUI 0163B

Copyright © 2001-2003. All rights reserved.

B-1

Image 85

Arm Enterprises IM-AD1 manual Mechanical Specification

Contents

Integrator/IM-AD1 User Guide Integrator/IM-AD1 Conformance Notices Copyright 2001-2003. All rights reserved Chapter Introduction Integrator/IM-AD1 User Guide Appendix a Signal Descriptions Preface About this book Using this bookIntended audience Further reading Typographical conventionsARM publications Third-party documents Feedback on this document FeedbackFeedback on the Integrator/IM-AD1 Xii Introduction ARM DUI 0163B About the Integrator/IM-AD1 Integrator/IM-AD1 layout Features Interface module features and architecture Architecture Integrator/IM-AD1 block diagram Links and LEDs Config LED Care of modules Introduction Copyright 2001-2003. All rights reserved Getting Started Assembled Integrator development system Fitting the interface module Switch 2 Closed Switch 3 Open Switch 4 Open Setting up the logic module Running the test software Hardware Reference Hardware Reference Connector Serial interface signal assignment Signal nameUart interface Description Serial connector signal assignment Pin J18 Type Description Serial connector pinout SPI SPI signals Signal PWM interface PWM interface signals Signal PWM connector signals Pin J14 J10 Description Shows the signal assignment Functional description Stepper motor interface Therefore, with a 0.1Ω sense resistor fitted Stepper motor interface signal summary Stepper motor interface signals Stepper motor connectors VSS Stepper motor connector signals Pin J19 J23 Description Gpio Gpio connectors J16 and J17 Hardware Reference U13 Can interfaceBuffer Can interface signal assignment Signal IMBBANK29 IMBBANK28IMBBANK30 GND Can connector signal assignments Pin 10 ADC and DAC interface architecture ADC and DAC interfaces IMABANK49 IMABANK48IMABANK50 IMABANK51 11shows the pinout of the ADC interface connector J1 12 shows the pinout of the DAC interface connector J2 Hardware Reference Copyright 2001-2003. All rights reserved Reference Design Example About PrimeCells About the design exampleExample architecture File Description Vhdl file descriptions Example memory map Integrator system memory map Address assignment of logic modules Logic module addresses Position Bits Stack Integrator/IM-AD1 memory mapIntegrator/IM-AD1 memory map Device Address Gpioa StepperbGpiob Ssram Logic module registers Example APB register peripheralOffset address Name Type Function Oscillator divisor registers RDW LMOSCx registers Bits Name Access FunctionVDW Oscillator lock register Bits Name Access FunctionUser LEDs control register Push button interrupt register Switches register Uart SPICS2 SPI chip select registerSPICS1 SPICS0 Synchronous serial port PWM controller Stepper motor peripheral Offset Name Access Function AddressCont Count Stepper x control register Singlestep DocountDIR Stepx speed register Stepx count register Address offset Name Access Size Function Read data output pinsData output set register Read data input register Gpio direction control 1 bit Data direction Ssram interface Interrupt sources Vectored interrupt controllerInterrupt Interrupt source Source number CAN1 Reference Design Example Canreset Can reset control registerCan controller interface CANxBase 16 ADC and DAC interface registers ADC and DAC interfaceAdcstatus ADC2BUSY 18 PIB entry format Peripheral information blockBits Name Function Signal Descriptions Expa Pin label Signal Description Table A-1 AHB signal assignment Expb Pin label Name Description Table A-2 Expb signal description Expim Label Table A-3 Expim signal descriptionsLM-EP20K1000E Description Figure A-4 J7 pin locations Logic analyzer connector CLK1 Table A-4 J7 connector pinout Signal Pin Multi-ICE Jtag Figure A-5 Multi-ICE connector pinout Mechanical Specification Mechanical information Figure B-1 Board dimensions top view Figure B-2 Bottom board dimensions viewed from top side DB9DUAL Connector referenceDB9STRAIGHT FCI Multi-ICE Glossary Synchronous Serial Port ADC Can IndexDAC Gpio Gpiodataclr Gpiodatain Gpiodataout Gpiodataset Gpiodirn Expa A-2Lmleds Lmlock LMOSC1