Connector reference, DB9DUAL | Arm Enterprises IM-AD1 specs

Mechanical Specification

B.2 Connector reference

Table B-1 lists the connectors on the IM-AD1. Two Weidmuller BL3.5/6 SN OR plugs and two BL3.5/4 SN OR plugs are supplied in a separate plastic bag. These mate with J10, J14, J19, and J23.

Table B-1 connector reference

Reference	Type	Manufacturer	Part number

J1	CON34_0.1"_34W_RA	Toby	302-R-34-D1-S1

J2	CON10_0.1"_10W_RA	Toby	302-R-10-D1-S1

J11	CON10_0.1"_10W_RA	Toby	302-R-10-D1-S1

J13	CON10_0.1"_10W_RA	Toby	302-R-10-D1-S1

J3	DB9_DUAL	Toby	DMR-DP-09P/09P-G-15.87

J5	SOLC-150-02-F-Q_0.64mm pitch	Samtec	SOLC-150-02-F-Q-P-A

J4	SOLC-150-02-F-Q_0.64mm pitch	Samtec	SOLC-150-02-F-Q-P-A

J6	SOLC-130-02-F-Q_0.64mm pitch	Samtec	SOLC-130-02-F-Q-P-A

J7	Mictor_38 way	Agilent	2-767004-2

J8	2x1_pin_header_0.1"_2W_LINK	Toby	THS-2-S

J9	CON20AP_0.1"_20W_VERT	Toby	302-S-20-D1-S1

J10	CON4_3.5mm_4W_RA	Weidmuller	SL 3.5/4/90G 3.2 SN OR

J14	CON4_3.5mm_4W_RA	Weidmuller	SL 3.5/4/90G 3.2 SN OR

J16	CON50_0.1"_50W_VERT	Toby	302-S-50-D1-S1

J17	CON50_0.1"_50W_VERT	Toby	302-S-50-D1-S1

J18	DB9_STRAIGHT	FCI	D09P24A4GV00

J19	CON6_3.5mm_6W_RA	Weidmuller	SL 3.5/6/90G 3.2 SN OR

J23	CON6_3.5mm_6W_RA	Weidmuller	SL 3.5/6/90G 3.2 SN OR

J21	CON10_0.1"_10W_VERT	Toby	302-S-10-D1-S1

J22	CON10_0.1"_10W_VERT	Toby	302-S-10-D1-S1

B-4

Copyright © 2001-2003. All rights reserved.

ARM DUI 0163B

Image 88

Arm Enterprises IM-AD1 manual Connector reference, DB9DUAL, DB9STRAIGHT FCI

Contents

Integrator/IM-AD1 Integrator/IM-AD1 User Guide Conformance Notices Copyright 2001-2003. All rights reserved Integrator/IM-AD1 User Guide Chapter Introduction Appendix a Signal Descriptions Preface About this book Using this bookIntended audience Further reading Typographical conventionsARM publications Third-party documents Feedback on this document FeedbackFeedback on the Integrator/IM-AD1 Xii Introduction About the Integrator/IM-AD1 ARM DUI 0163B Integrator/IM-AD1 layout Interface module features and architecture Features Integrator/IM-AD1 block diagram Architecture Config LED Links and LEDs Care of modules Introduction Copyright 2001-2003. All rights reserved Getting Started Fitting the interface module Assembled Integrator development system Setting up the logic module Switch 2 Closed Switch 3 Open Switch 4 Open Running the test software Hardware Reference Hardware Reference Serial interface signal assignment Signal name ConnectorUart interface Description Serial connector pinout Serial connector signal assignment Pin J18 Type Description SPI signals Signal SPI PWM interface signals Signal PWM interface Shows the signal assignment PWM connector signals Pin J14 J10 Description Stepper motor interface Functional description Stepper motor interface signal summary Therefore, with a 0.1Ω sense resistor fitted Stepper motor connectors Stepper motor interface signals Stepper motor connector signals Pin J19 J23 Description VSS Gpio connectors J16 and J17 Gpio Hardware Reference U13 Can interfaceBuffer Can interface signal assignment Signal IMBBANK29 IMBBANK28IMBBANK30 Can connector signal assignments Pin GND ADC and DAC interfaces 10 ADC and DAC interface architecture IMABANK48 IMABANK49IMABANK50 IMABANK51 11shows the pinout of the ADC interface connector J1 12 shows the pinout of the DAC interface connector J2 Hardware Reference Copyright 2001-2003. All rights reserved Reference Design Example About PrimeCells About the design exampleExample architecture Vhdl file descriptions File Description Example memory map Address assignment of logic modules Integrator system memory map Logic module addresses Position Bits Stack Integrator/IM-AD1 memory mapIntegrator/IM-AD1 memory map Device Address Stepperb GpioaGpiob Ssram Logic module registers Example APB register peripheralOffset address Name Type Function Oscillator divisor registers RDW LMOSCx registers Bits Name Access FunctionVDW Bits Name Access Function Oscillator lock registerUser LEDs control register Push button interrupt register Switches register Uart SPI chip select register SPICS2SPICS1 SPICS0 Synchronous serial port PWM controller Offset Name Access Function Address Stepper motor peripheralCont Count Stepper x control register Singlestep DocountDIR Stepx count register Stepx speed register Read data output pins Address offset Name Access Size FunctionData output set register Read data input register Data direction Gpio direction control 1 bit Ssram interface Vectored interrupt controller Interrupt sourcesInterrupt Interrupt source Source number CAN1 Reference Design Example Can reset control register CanresetCan controller interface CANxBase ADC and DAC interface 16 ADC and DAC interface registersAdcstatus ADC2BUSY 18 PIB entry format Peripheral information blockBits Name Function Signal Descriptions Expa Table A-1 AHB signal assignment Pin label Signal Description Expb Table A-2 Expb signal description Pin label Name Description Expim Label Table A-3 Expim signal descriptionsLM-EP20K1000E Description Logic analyzer connector Figure A-4 J7 pin locations Table A-4 J7 connector pinout Signal Pin CLK1 Figure A-5 Multi-ICE connector pinout Multi-ICE Jtag Mechanical Specification Figure B-1 Board dimensions top view Mechanical information Figure B-2 Bottom board dimensions viewed from top side DB9DUAL Connector referenceDB9STRAIGHT FCI Glossary Multi-ICE Synchronous Serial Port Index ADC CanDAC Gpio Gpiodataclr Gpiodatain Gpiodataout Gpiodataset Gpiodirn Expa A-2Lmleds Lmlock LMOSC1