Cleveland Range inverter manual Parameter List, P Gain

Chapter 3 - Parameter List

		Keypad			Factory	Adj.
Code	Description		Setting Range	Units		During	Page
		Display			Default
						Run
FU2-24	P Gain	H 24	0 to 9999	1	100	Yes	53
	During Speed Search
FU2-25	I Gain	H 25	0 to 9999	1	5000	Yes	53
	During speed search
FU2-26	Number of Auto Restart Attempt	H 26	0 to 10	1	0	Yes	54
FU2-27	Delay Time before Auto Restart	H 27	0 to 60 [sec]	0.1	1.0 [sec]	Yes
			0.4 (0.37kW)
			0.8 (0.75kW)
FU2-30	Rated Motor Selection	H 30	1.5 (1.5kW)	-	13	No	54
			2.2 (2.2kW)
			3.7 (3.7kW)
			4.0 (4.0kW)
FU2-31	Number of Motor Pole	H 31	2 to 12	1	4	No
FU2-3214	Rated Motor Slip	H 32	0 to 10 [Hz]	0.01		No
FU2-33	Rated Motor Current in RMS	H 33	0.1 to 99.9 [A]	1	14	No	54
FU2-3415	No Load Motor Current in RMS	H 34	0.1 to 99.9 [A]	1		No
FU2-36	Motor Efficiency	H 36	50 to 100 [%]	1		No
FU2-37	Load Inertia	H 37	0 to 2	1	0	No
FU2-39	Carrier Frequency	H 39	1 to 10 [kHz]	1	3 [kHz]	Yes	55
FU2-40	Control Mode Selection	H 40	0 (V/F)	-	0 (V/F)	No	56
			1 (Slip Compen)
			2 (PID)
FU2-5016	PID Feedback Signal Selection	H 50	0 (I)	-	I	No
			1 (V1)		0
FU2-51	P Gain for PID Control	H 51	0 to 9999	1	3000	Yes	56
FU2-52	I Gain for PID Control	H 52	0 to 9999	1	300	Yes
FU2-53	D Gain for PID Control	H 53	0 to 9999	1	0	Yes
FU2-54	Limit Frequency for PID Control	H 54	0 to FU1-20	0.01	50 / 60 [Hz]	Yes
FU2-70	Reference Frequency for Accel and	H 70	0 (Max Freq)	-	Max frq	No	57
	Decel		1 (Delta Freq)		0
FU2-71	Accel/Decel Time Scale	H 71	0 (0.01 sec)	-	1 (0.1 sec)	Yes	58
			1 (0.1 sec)
			2 (1 sec)
FU2-72	Power On Display	H 72	0 (Cmd. Freq)	1	0	Yes	58
			1 (Acc. Time)		(Cmd. Freq)
			2 (Dec. Time)

13The rated motor is automatically set according to the inverter model number. If a different motor is used, set the correct motor parameters.

14This value is automatically entered according to the rated motor set in FU2-30. If different, set the correct motor parameters.

15Code FU2-32 and FU2-34 appear only when FU2-40 is set to ‘Slip comp’.

16Code FU2-50 through FU2-54 appears only when FU2-40 is set to ‘PID’.

28