Chapter 4 - Parameter Description [FU2]

FU2-75: DB (Dynamic Braking) Resistor Mode Selection

This code is used to protect the DB resistor from over heating.

Setting Range

Description

Select

Display

 

None

0

This is selected when there is no resistor

 

 

connected. At this time, inverter does not

None

1

generate DB turn on signal.

 

 

This is selected when using an external

Ext. DB-R

2

DB resistor.

Enable Duty (%): 0 ~ 30 %

 

 

 

 

Continuous Turn On Time: 15 seconds

The inverter turns the DB turn on signal OFF when the Continuous Turn On Time expires during dynamic braking, and an over voltage fault can occur. When this happens, increase the deceleration time or install an external high-duty DB resistor.

Install an exterior high-duty DB resistor when the load accelerates and decelerates frequently. Set the FU2-75 [DB Resistor Mode selection] to ‘Ext. DB-R’, and set the FU2-76 [Duty of DB Resistor].

FU2-76: Duty of DB (Dynamic Braking) Resistor

This must be set when using an external DB resistor. The duty is calculated by ‘%ED=Decel time * 100 / (Accel time + Steady speed time + Decel time + Stop status time)’.

FU2-79: Software Version

Displays the software version.

FU2-81 ~ FU2-90: 2nd Motor Related Functions

These functions are displayed only when one of the multifunction inputs is set at ‘2nd func’ in I/O- 12 to I/O-14.

When using two motors with an inverter by exchanging them, different values can be set for the 2nd motor by using the multifunction input terminal.

Following table is the 2nd functions corresponding to the 1st functions.

2nd Functions

1st Functions

Description

FU2-81

DRV-01

Acceleration time

[2nd Acc time]

[Acc. time]

 

FU2-82

DRV-02

Deceleration time

[2nd Dec time]

[Dec. time]

 

FU2-83

FU1-21

Base Frequency

[2nd Base Freq]

[Base freq]

 

FU2-84

FU1-29

Volts/Hz mode

[2nd V/F]

[V/F Pattern]

 

FU2-85

FU1-27

Forward torque boost

[2nd F-boost]

[Fwd Boost]

 

FU2-86

FU1-28

Reverse torque boost

[2nd R-boost]

[Rev Boost]

 

FU2-87

FU1-60

Stall prevention level

[2nd Stall]

[Stall Level]

 

FU2-88

FU1-51

ETH level for 1 minute

[2nd ETH 1min]

[ETH 1min]

 

FU2-88

FU1-52

ETH level for continuous

[2nd ETH cont]

[ETH cont]

 

FU2-90

FU2-33

Motor rated current

[2nd R-Curr]

[Rated-Curr]

 

59

Page 65
Image 65
Cleveland Range inverter manual FU2-76 Duty of DB Dynamic Braking Resistor, FU2-79 Software Version

inverter specifications

The Cleveland Range inverter is a state-of-the-art piece of kitchen equipment designed to elevate cooking efficiency and precision in commercial kitchens. This versatile appliance is particularly well-suited for establishments such as restaurants, cafeterias, and catering operations, where high-performance and reliability are critical to success.

One of the standout features of the Cleveland Range inverter is its innovative inverter technology. Unlike traditional cooking equipment that utilizes standard heating elements, the inverter system allows for continuous, variable power control. This means that cooks can seamlessly adjust the cooking temperature, offering unparalleled control over the cooking process. The result is more consistent cooking outcomes and a significant reduction in food preparation time, ensuring that dishes are cooked just right every time.

Another characteristic that sets the Cleveland Range inverter apart is its energy efficiency. The inverter technology not only enhances cooking precision but also utilizes energy more effectively, leading to reduced power consumption. This is particularly beneficial for commercial kitchens where energy costs can quickly add up. By minimizing energy waste, the Cleveland Range inverter contributes to a more sustainable kitchen operation.

Safety is also a prime focus of the Cleveland Range inverter. With built-in safety features such as automatic shut-off functions, the appliance ensures that accidental overheating or overcooking is avoided, safeguarding both the kitchen staff and the food being prepared. Additionally, the design of the inverter is user-friendly, making it accessible for cooks at all experience levels.

Durability and ease of maintenance are further characteristics of the Cleveland Range inverter. Built with high-quality materials and a robust construction, it is designed to withstand the rigors of a busy kitchen environment. The straightforward design allows for easy cleaning and maintenance, ensuring that the inverter remains in top working condition over its lifespan.

In conclusion, the Cleveland Range inverter stands out in the commercial kitchen landscape due to its innovative inverter technology, energy efficiency, safety features, and durability. It is an excellent investment for any culinary operation looking to enhance its cooking capabilities while maintaining high standards of food quality and safety. This appliance not only meets the demands of modern kitchens but also sets a benchmark for others in the industry.