any other 5 digit number, if you wish, as explained later (*45). When in the MANUAL mode, the letter "M" shows at the left end of display.

The following manual functions are available in the MANUAL mode.

OPERATE: Press once followed by one of 16 keys: 1 through 9, A, B,

(OPER) C, DUMP, ALRM, MIX, or HOLD. The selected output operates until the key is pressed again or another output is selected. Only 1 output will be active at a time.

EXIT will exit the sequence and close all outputs.

TIMED:

Press

once

followed by one

of

12 component

keys.

A time in

(TIME)

interrupts

is requested; (TIME

---).

Three digits must

be

 

entered specifying

a dispense

time up

to 999 interrupts

 

 

(about 4

seconds maximum.)

CE

will

cancel

entry before

last

 

digit

is

entered.

Following a

full

3

digit time

entry,

the

specified output is activated for the time requested. After the dispense is weighed, the dump valve automatically operates to empty the weigh bin. If a printer is on line and the Print flag is ON, then output information will be printed. EXIT will exit the sequence.

CALIBRATE: (RATE) Press once followed by one of the 12 component keys.

(CAL) A dispense will occur for 2 seconds. If the amount dispensed is less then 50 grams, a second dispense will occur for 20 seconds. Using the resulting weight and time, the processor calculates a proper beginning point dump rate for the start of production blending. After each dispense is weighed, the weigh bin dump valve automatically operates to empty the weigh bin. If a printer is on line and the Print flag is ON (see KEYPAD *54), then output information will be printed. EXIT will exit the sequence.

If the display says (DO AGAIN), press any key to cause the process to repeat itself. If the display then says

( NO GOOD), the dispense weight was below 2 grams, not enough for a valid calibration.

During initial operation, after each power up, the blender calibrates itself completely automatically, regardless of how far off the initial flow rate may be. This may take several cycles. During normal operation, calibration correction occurs continuously.

Since this unit adjusts flow rates automatically, manual Rate Calibration is not necessary for proper operation.

ZERO WT.

THIS HAS BEEN DONE AT THE

FACTORY. IT SHOULD NOT

BE

(ZERO)

NECESSARY FOR YOU TO DO THIS AGAIN.

 

 

For this key to function,

you must first set the

weight

 

calibration flag ON. Press *99 to observe flag status.

 

Press * to toggle flag ON

or OFF. With flag set ON, press

 

EXIT. Power-off always resets this flag to OFF.

 

Press the ZERO key once to set the displayed gram weight of the empty bin to zero. BE SURE the load cells are plugged into the controller. Be sure the bin is properly in place

Page 35

Page 34
Image 34
Conair WSB, GB manual Timed

GB, WSB specifications

The Conair WSB,GB represents a cutting-edge advancement in hair styling technology designed for both professionals and everyday users. Known for its versatility, this styling device merges high-performance with user-friendly characteristics to deliver exceptional results.

One of the standout features of the Conair WSB,GB is its dual voltage capability. This allows users to take it anywhere in the world without worrying about voltage inconsistencies, making it an ideal travel companion. The device's sleek and portable design ensures that it is easy to pack while still being robust enough to handle regular usage.

The WSB,GB incorporates advanced heating technology that ensures rapid heat-up times, allowing users to get to styling quickly. With multiple heat settings, the device caters to various hair types and styles, whether it's coarse, fine, or color-treated hair. This customization is essential for achieving the perfect look while minimizing damage.

Another impressive characteristic of the Conair WSB,GB is its innovative ceramic technology. The ceramic plates distribute heat evenly, reducing hot spots that can lead to hair damage. This feature ensures that styling is not only efficient but also gentle on the hair, promoting a healthy shine and reducing frizz for a polished finish.

The device also boasts a swivel cord, which enhances convenience during use by allowing for free movement without the hassle of tangling. This ergonomic consideration is particularly beneficial for professional hairstylists who may need to maneuver around clients during appointments.

Safety is a crucial aspect of the WSB,GB design. It includes an automatic shut-off feature that turns the device off after a period of inactivity, providing peace of mind for users who might accidentally leave it on when finished.

In summary, the Conair WSB,GB offers various features that cater to the modern user’s needs. With its dual voltage, rapid heating capabilities, ceramic technology, swivel cord, and safety features, it stands out in the crowded hair styling market. Whether you’re a professional stylist or someone looking to elevate your everyday look, the WSB,GB is engineered to meet these demands with excellence.