1204 = 1205 = | DCS 500 specs

Chapter 2 - Start-Up Instructions

1204 = 0

1205 = 0

Switch OFF power, thus stopping the drive!

1701 = 11903

501 = Rated motor voltage set in Chapter 2.2.

1012 = Speed at rated motor voltage

CAUTION! Please don't forget!

11202 = SAVE MOT1 SET

Save the altered values in the non-volatile memory!

2.8Matching the thyristor power converter unit to the system conditions concerned

-Ramp function generator

-Binary inputs and outputs

-Limit-value messages

-Additional functions

DCS 500B / DCP 500B Operating Instructions

IV A 2 - 21

3ADW000055R0401_DCS500B_Operating Instruction_e_d

Image 33

DCS 500 manual 1204 = 1205 =

Contents

DCS 500B / DCF 500B DCP 500B How the DCS 500 Documentation System works Operating Instructions DCS 500B / DCP 500B Operating Instructions Overview Safety Instructions Safety Instructions Mains connection Emergency Stop buttons Intended use Contents Signals and Troubleshooting DCS 500B / DCP 500B Operating Instructions Contents of this manual How to use this manualTarget group Associated publications Incoming inspection Storage and transportRating plate How this chapter is structured General notesRecommended motor voltages and field voltages = Line voltage Method of functioning of the binary inputs DI5, DI7 and DI8 System-dependent planning Symbols for enabling / disabling the reference Symbol for measuring physical variables Symbol for displaying parameter values or connections Preparatory work Scaling intra-unit signals Set this only for units of the DCP 500 series 518 = 500 V fixed! rated power converter voltage519 11202 = Save MOT1 SET 1305 = Field current for Under-excitation signal Presetting the field supply unit IV a 2 1201 = 3 Panel display ARM. Autotuning Adjusting the current controller DCS 500B / DCP 500B Operating Instructions IV a 2 Speed feedback balancing Only when the e.m.f. signal is being used as speed feedback Continue with Chapter Balancing the field supply unit and the e.m.f. controller Field weakening control with setting range 1 If the field time constant is not known 1204 = 1205 =11209 = 1002 = 1201 = 0 Panel display not Activated 11202 = Save MOT1 SET1004 = 1009 = 1010 = = decrease so that motor voltage is 70% 11003Proceed as described in 1. / 2. / 3. above = decrease so that motor voltage is 40% 12516 = increase slowly up to 20000 =100 % speed Only if analog tacho is used as speed feedback 1204 POT1 = 10%...20% max. speed 1708 = 0,1 s 1709 = 0,1 s408 = desired response behaviour of controller 1008 = desired response behaviour of controller 1204 = 1205 = Presetting the 3-phase field supply unit DCF 50xB 3601 = 1201 = 5Panel display FEX2/3 Autotuning3602 = 3603 = 1201 = 4Panel display ARM. MAN. Tuning ⇒ CDP ⇒ CDP 310 or CDP ID-NUMBER Total 1 Drives Start Mode Panel Functions ACT PAR Pin/Parameter Selecting and Changing of Value Drive Mode Value To enter the Parameter Mode Backupstoremode Saving of the Parameters to backup memory Display Mode Fault Resetting Reset Fault History Display DCS Uploading and Downloading of Parameters UPLOAD/DOWNLOAD DCS 500B / DCP 500B Operating Instructions IV a 3 Setting of the Display Contrast Full Name of output pinsDisplay Mode release key Selecting output pins Drive Mode Operational Com- mand Keys Running the Drive To enter the Reference Setting Speed Reference Setting for the DriveTo exit the Reference Setting Mode Display of status, alarm and fault signals Signals and Troubleshooting General messages Starting errors E Auxil. undervoltage Fault Signals F Conv.fan curr.fault Earth faultMotor 1 overtemp SDCS-IOB-3, SDCS-POW P418 Local & discon Ext.Overvolt.FaultNected Limited by the activation of a free wheeling Circuit Field ex.1 comerror Mains overvoltageCheck Parameters of Field Exciter Arm. curent ripple No ext. FAN ack See Fault Code FNo main cont. ack Field ex.1 not OK IV a 4 Current Difference Reversal Fault 103 Motor 1 temp. alarm Alarm Signals aCheck See Fault Code F 105 Conv. overtemp 101 Start inhibition 110 108118 120 128 127129 130 136 134137 138 At Macro x, macro-specific links or function 11201 Status Signals Backupstoremode Fexcstatus 11203 11205 11204 DCF 500B IV a a IV a a 055R0401A2440000