Manuals / DCS / Computer Equipment / Power Supply

DCS 500 manual Panel Functions, Actual Signal Display Mode, IV A 3

Models: 500

1 76

Download 76 pages 28.4 Kb

Page 39

3.3 Panel Functions

3.3 Panel Functions

Actual Signal

Display Mode

ACT

Chapter 3 - Handling of Control Panel CDP 31x

The CDP 31x has four different keypad modes:

•Actual Signal Display Mode (ACT)

•Parameter Mode (PAR)

•Function Mode (FUNC)

•Drive Mode (DRIVE) for further extensions

This keypad mode will show, depending on the drive´s history:

•Actual Signals

•Faults

•Fault History Logger

If the ACT-key is pressed immediately after initialization this table is displayed. If no panel-key is touched for more than one minute the Actual Signal Display will appear automatically, except when Status display or speed reference setting is active. (see chapter 3.13 and 3.15)

Actual Signal Display

ID-number	Control	Speed	Main contactor	Run Status
of the Drive	Location	reference	status	I = RUN
	L = Local	rpm	0 = Open	0 = STOP

			= Remote				1 = Closed

	Statusrow
						0 L	0.0 rpm 00
	Actual Signal
						SPEED AC	0.0	rpm

	Name, value and unit					CONV CUR	0	A

	Cursor shows					U ARM AC	0	V

						_

the selected row

If a fault is effective in the drive, the Fault Display will appear auto- matically. This will happen with all other modes as well, except the Drive Mode is active.

Fault Display

			0 L	0.0	rpm 00
			DCS 500
			* FAULT *
Type of fault or alarm			No ext. FAN ack.
Type of fault or alarm			No ext. FAN ack.

To select Fault History Display see chapter 3.8

Fault History Display

1	= last fault				0	L	0.0	rpm 00

2	= second last fault			1		LAST FAULT
...
Fault or alarm name					I/O-Board not			found

Total time after
the power up				0000:14:12.64

HHHH:MM:SS.ss

DCS 500B / DCP 500B Operating Instructions

IV A 3 - 3

3ADW000055R0401_DCS500B_Operating Instruction_e_d

Image 39

DCS 500 manual Panel Functions, Actual Signal Display Mode ACT Parameter Mode PAR Function Mode FUNC, IV A 3

Contents

DCS 500B / DCF 500B DCP 500B DCS 500 Thyristor Power Convertersfor DC Drive Systems 25 to 5150 A Operating InstructionsHow the DCS 500 Documentation System works OPERATING INSTRUCTIONS Thyristor Power Converters SeriesDCS 500B / DCF 500B DCP 500B 25 to 5150 A3ADW000055R0401DCS500BOperating Instructioned DCS 500B / DCP 500B Operating InstructionsDCS 500B / DCP 500B Operating Instructions Safety InstructionsOverview WarningsWarning of electrostatic discharge Safety InstructionsMains connection EMERGENCY STOP buttons Intended use Safety InstructionsDCS 500B / DCP 500B Operating Instructions Chapter 3 - Handling of Control Panel CDP ContentsSafety Instructions IV A OPERATING INSTRUCTIONSRunning the DC- Drive from the CDP31x ContentsChapter 4 - Signals and Troubleshooting Appendix A - Connection diagrams3ADW000055R0401DCS500BOperating Instructioned DCS 500B / DCP 500B Operating InstructionsTechnical Data DCS 500B / DCF 500B, DCP 500B How to use this manualContents of this manual Chapter 3 - How to Handle the Control and Display PanelDCS 500B / DCF 500B or DCP 500B Incoming inspectionStorage and transport Rating plateHow this chapter is structured Chapter 2 - Start-Up InstructionsGeneral notes IV A 2Range of application for the Start-Up Instructions Phase sequence when connecting to the mains / Potential isolationIV A 2 Preventing unintended operating states / Shutting the drive downIV A 2 Symbols for switching the electronics or the power section ON and OFFSymbols for enabling / disabling the reference System-dependent planningIV A 2 Symbol for altering parameters or for establishing new connectionsSymbol for displaying parameter values or connections Symbol for measuring physical variables2.1 Preparatory work IV A 2DCS 500B / DCP 500B Operating Instructions = Rated power converter supply voltage 2.2 Scaling intra-unit signalsOnly when connection diagram 1 Appendix A is being used 906 = = Rated power converter currentCAUTION! Please dont forget 11202 = SAVE MOT1 SET = 500 V fixed! rated power converter voltageSet this only for units of the DCP 500 series = Rated line voltage505 = 2.3 Presetting the field supply unit1305 = Field current for Under-excitation signal Only for uncontrolled field supply with SDCS-FEX-1505 = 2Panel display FEX2 OR FEX3 503 = Rated motor field current Panel display FEX2/3 AUTOTUNING1201 = Only for controlled field supply with DCF 501B or DCF 502B11202 2.4 Adjusting the current controller1201 = 3 Panel display ARM. AUTOTUNING Panel display NO FIELD EXCITERDCS 500B / DCP 500B Operating Instructions b 505 =1201 = 3 Panel display ARM. AUTOTUNING CAUTION! Please dont forget 11202 = SAVE MOT1 SET1701 = Only when an analog tacho is being used2.5 Speed feedback balancing 1001 = 0 Panel display CONSTANT FIELDCAUTION! Please dont forget 11202 = SAVE MOT1 SET Only when an encoder pulse encoder is being used12104 = Content of pulse counter Only when the e.m.f. signal is being used as speed feedbackContinue with Chapter 2.6 Balancing the field supply unit and the e.m.f. controller2.6.1 Constant field current control 12516 =CAUTION! Please dont forget 11202 = SAVE MOT1 SET 2.6.2 Field weakening control with setting range 11012 = Speed at field weakening point as per motor rating plate 12516 =If the field time constant is not known 2.6.3 Field weakening control with setting range 1Only when unit is fitted with an SDCS-CON-1 control board If the field time constant is known, e.g. from the motor data sheet1009 = 1010 = 1201 = 0 Panel display NOT ACTIVATED 11202 = SAVE MOT1 SET1002 = 1004 == decrease so that motor voltage is 40% 11003= decrease so that motor voltage is 70% Proceed as described in 1. / 2. / 3. aboveCAUTION! Please dont forget 11202 = SAVE MOT1 SET Only if analog tacho is used as speed feedback12516 = increase slowly up to 20000 =100 % speed 12516 =2018 = desired response behaviour of controller Only when fine-balancing of the current controller is wanted1708 = 0,1 s 1709 = 0,1 s 1204 POT1 = 10%...20% max. speed11202 = SAVE MOT1 SET 1701 = 501 = Rated motor voltage set in Chapter1012 = Speed at rated motor voltage CAUTION! Please dont forget 1204 = 1205 =409 = 2.9 Presetting the 3-phase field supply unit DCF 50xB1217 = 0 or 1 Panel display OVP ALARM or OVP ALARM 402 =3603 = 1201 = 5Panel display FEX2/3 AUTOTUNING3601 = 3602 =Continue with Chapter 1201 = 4Panel display ARM. MAN. TUNING1215 = 4Panel display FEXLINK NODE 11202 = SAVE MOT1 SET⇒ CDP 310 or CDP Chapter 3 - Handling of Control Panel CDP3.1 Overview IV A 3IV A 3 3.2 Start ModeIV A 3 Actual Signal Display ModeActual Signal Display Mode ACT Parameter Mode PAR Function Mode FUNC 3.3 Panel FunctionsFunction Mode FUNCIV A 3 3.4 Pin/Parameter Selecting and Changing of Value Drive ModeThe factory-adjusted default values of the ID-numbers for the DRIVEelement number To enter the Parameter Modevalue IV A 3DCS 500B / DCP 500B Operating Instructions 3.5 Saving of the Parameters to backup memoryTo enter the Parameter Mode IV A 3IV A 3 3.6 FAULT RESETTING RESET3.7 EMERGENCY STOP RESETTING RESET Display ModeSignal Display 3.8 Fault History Displayscreen from Actual Signal Dis play to Fault Display , to FaultIV A 3 3.9 Uploading and Downloading of Parameters UPLOAD/DOWNLOADTo enter the Function Mode DCS 500B / DCP 500B Operating InstructionsIV A 3 IV A 3 3.10 Setting of the Display Contrast3.11 Full Name of output pins Display Mode release keyDisplay Mode 3.12 Selecting output pinsNote for CDP 310 / CDP Note for CDPIV A 3 3.13 Drive ModeIf LOC is activated some of the 3.14 Running the DriveOperational Com- mand Keys Running the DC Drive from the CDP31xMode 3.15 Speed Reference Setting for the DriveTo enter the Reference Setting To exit the Reference SettingIV A 4 Chapter 4 - Signals and Troubleshooting4.1 Display of status, alarm and fault signals Categories of signalsIV A 4 4.3 Starting errors EChapter 4 - Signals and Troubleshooting 4.2 General messagesfor faults or blocking condition 4.4 Fault Signals FTry to reset. Check internal auxiliary volt ages if fault persists, change SDCS-CON-xChapter 4 - Signals and Troubleshooting Conv.fan curr.faultEarth fault F 6 Motor 1 overtempIV A 4 P418Chapter 4 - Signals and Troubleshooting Current rise faultSetting of OVPSELECT Ext.Overvolt.FaultCheck - Power wiring of the field supply Control logic according to wiringMains voltage 130% of nominal value for Fault tracing see Fault Code FF 33 Field ex.1 comerror Mains overvoltagepower supply for the field unit not within permissi Chapter 4 - Signals and Troubleshootingmissing „ready for operation“ signal 1 or the field electronic power supply for the field unit not withinF 42 Field ex.1 not OK See Fault Code FF 40 No ext. FAN ack F 41 No main cont. ackSDCS-CON-x and SDCS-IOB-1/2x/3/IOE1 IV A 4Chapter 4 - Signals and Troubleshooting  /3DCS 500B / DCP 500B Operating Instructions Reversal FaultF 66 Current Difference Chapter 4 - Signals and Troubleshootingnal will be reset 4.5 Alarm Signals A1“ drive cannot be switched ON When pin is set to logical 0“, the alarm sigS21.232 Chapter 4 - Signals and TroubleshootingDCS 500B / DCP 500B Operating Instructions IV A 4IV A 4 Chapter 4 - Signals and Troubleshootingnot be re Chapter 4 - Signals and TroubleshootingDCS 500B / DCP 500B Operating Instructions IV A 4blocks have been changed in comparison Chapter 4 - Signals and TroubleshootingSignal At Macro x, macro-specific links or functionChapter 4 - Signals and Troubleshooting 4.6 Status Signals11201 COMMISSTAT11202 BACKUPSTOREMODEChapter 4 - Signals and Troubleshooting 1120111202 11203FEXCSTATUS Chapter 4 - Signals and TroubleshootingChapter 4 - Signals and Troubleshooting 11204TCSTATUS 11205Instructions DCS 500B / DCP 500B OperatingSystem description DCF 500B500B / DCF 500B IV A Adescription DCS 500BDCS 500B / DCP 500B Operating Instructions IV A A055R0401A2440000 055R0401A2440000