1201 = 4Panel display ARM. MAN. Tuning | DCS 500 instruction

Chapter 2 - Start-Up Instructions

When the display shows NOT ACTIVATED (action correctly completed):

Stop drive

Switch OFF power!

In case the autotuning failed:

1201 = 4Panel display: ARM. MAN. TUNING

ARM.MAN_TUNING, if the FEX2/3 autotuning failed; activate the reference via pa- rameter 11209 and set the parameters of the square wave function generator; then adapt the current controller to get the behaviour shown at curve D chapter 2.6.3 in this manual

1215 = 4Panel display: FEXLINK NODE 1

DCF mode FEXLINK NODE1 via FEX-link activated

11202 = SAVE MOT1 SET

Save the altered values in the non-volatile memory!

The DCS converter in DCF-mode (parameter 1215=1 or higher) will not accept a start command, if an alarm or fault is still active (an A or F indication on the 7-segment dis- play). To ensure a correct function afterwards, please make sure the reasons for any type of alarm or fault is no longer present.

Continue with Chapter 2.4

IV A 2 - 24

DCS 500B / DCP 500B Operating Instructions

3ADW000055R0401_DCS500B_Operating Instruction_e_d

Image 36

DCS 500 manual 1201 = 4Panel display ARM. MAN. Tuning, Continue with Chapter

Contents

DCS 500B / DCF 500B DCP 500B How the DCS 500 Documentation System works Operating Instructions DCS 500B / DCP 500B Operating Instructions Safety Instructions Overview Safety Instructions Mains connection Emergency Stop buttons Intended use Contents Signals and Troubleshooting DCS 500B / DCP 500B Operating Instructions How to use this manual Contents of this manualTarget group Associated publications Incoming inspection Storage and transportRating plate General notes How this chapter is structuredRecommended motor voltages and field voltages = Line voltage Method of functioning of the binary inputs DI5, DI7 and DI8 Symbols for enabling / disabling the reference System-dependent planning Symbol for displaying parameter values or connections Symbol for measuring physical variables Preparatory work Scaling intra-unit signals 518 = 500 V fixed! rated power converter voltage Set this only for units of the DCP 500 series519 11202 = Save MOT1 SET Presetting the field supply unit 1305 = Field current for Under-excitation signal IV a 2 Adjusting the current controller 1201 = 3 Panel display ARM. Autotuning DCS 500B / DCP 500B Operating Instructions IV a 2 Speed feedback balancing Only when the e.m.f. signal is being used as speed feedback Balancing the field supply unit and the e.m.f. controller Continue with Chapter Field weakening control with setting range 1 If the field time constant is not known 1204 = 1205 =11209 = 1201 = 0 Panel display not Activated 11202 = Save MOT1 SET 1002 =1004 = 1009 = 1010 = 11003 = decrease so that motor voltage is 70%Proceed as described in 1. / 2. / 3. above = decrease so that motor voltage is 40% Only if analog tacho is used as speed feedback 12516 = increase slowly up to 20000 =100 % speed 1708 = 0,1 s 1709 = 0,1 s 1204 POT1 = 10%...20% max. speed408 = desired response behaviour of controller 1008 = desired response behaviour of controller 1204 = 1205 = Presetting the 3-phase field supply unit DCF 50xB 1201 = 5Panel display FEX2/3 Autotuning 3601 =3602 = 3603 = 1201 = 4Panel display ARM. MAN. Tuning ⇒ CDP 310 or CDP ⇒ CDP Start Mode ID-NUMBER Total 1 Drives ACT Panel Functions PAR Drive Mode Pin/Parameter Selecting and Changing of Value To enter the Parameter Mode Value Saving of the Parameters to backup memory Backupstoremode Fault Resetting Reset Display Mode Fault History Display Uploading and Downloading of Parameters UPLOAD/DOWNLOAD DCS DCS 500B / DCP 500B Operating Instructions IV a 3 Setting of the Display Contrast Full Name of output pinsDisplay Mode release key Selecting output pins Drive Mode Running the Drive Operational Com- mand Keys Speed Reference Setting for the Drive To enter the Reference SettingTo exit the Reference Setting Mode Signals and Troubleshooting Display of status, alarm and fault signals Starting errors E General messages Fault Signals F Auxil. undervoltage Conv.fan curr.fault Earth faultMotor 1 overtemp P418 SDCS-IOB-3, SDCS-POW Ext.Overvolt.Fault Local & disconNected Limited by the activation of a free wheeling Circuit Field ex.1 comerror Mains overvoltageCheck Parameters of Field Exciter Arm. curent ripple See Fault Code F No ext. FAN ackNo main cont. ack Field ex.1 not OK IV a 4 Reversal Fault Current Difference Alarm Signals a 103 Motor 1 temp. alarmCheck See Fault Code F 105 Conv. overtemp 101 Start inhibition 108 110118 120 127 128129 130 134 136137 138 At Macro x, macro-specific links or function Status Signals 11201 Backupstoremode 11203 Fexcstatus 11204 11205 DCF 500B IV a a IV a a 055R0401A2440000