Running the Drive, Operational Com- mand Keys | DCS 500 instruction

3.14 Running the Drive

Operational Com- mand Keys

Chapter 3 - Handling of Control Panel CDP 31x

Operational commands can be given from the Control Panel CDP31x every time when the status row is displayed. Operational commands include START and STOP of the the drive, controlling the main contactor and adjusting the reference.

CAUTION! To be able to give operational commands from the CDP31x, the selected control location must be the Control Panel. The control location can be changed by means of LOC/REM key to LOCAL mode.

If LOC is activated some of the

binary inputs are no longer functioning.

Take care that the drive is engineered to allow opera- tion with LOCAL mode.

Control	Name of Key	Function
Panel Key

LOC	LOCAL /	To select LOCAL (= CDP31x) or REMOTE
	REMOTE	(= ext. control system) operation.

	START	Starts the drive, when in LOCAL mode.

	STOP	Stops the drive, when in LOCAL mode.

	ON	Main contactor closing control, when in
		LOCAL mode.

	OFF	Main contactor opening control, when in
		LOCAL mode.

Running the DC-

Drive from the CDP31x

M

Ensure safety before you start the drive test!

•Select LOCAL mode (LOCAL = CDP31x) by pressing LOC/REMOTE key.

•Close (switch on) the main contactor by pressing the ON key

•Start the drive by pressing the START key. Motor will now ac- celerate to the value of the reference.

•Direction of rotation can be changed by giving the opposite po- larity reference value in case of 4Q drive.

•Stop the drive by pressing the STOP key. Motor will decelerate to zero speed. (depending on the STOP MODE)

•Finally open (switch off) the main contactor by pressing the OFF key.

DCS 500B / DCP 500B Operating Instructions

IV A 3 - 15

3ADW000055R0401_DCS500B_Operating Instruction_e_d

Image 51

DCS 500 manual Running the Drive, Operational Com- mand Keys

Contents

DCS 500B / DCF 500B DCP 500B How the DCS 500 Documentation System works Operating Instructions DCS 500B / DCP 500B Operating Instructions Overview Safety Instructions Safety Instructions Mains connection Emergency Stop buttons Intended use Contents Signals and Troubleshooting DCS 500B / DCP 500B Operating Instructions Associated publications How to use this manualContents of this manual Target group Incoming inspection Storage and transportRating plate = Line voltage General notesHow this chapter is structured Recommended motor voltages and field voltages Method of functioning of the binary inputs DI5, DI7 and DI8 System-dependent planning Symbols for enabling / disabling the reference Symbol for measuring physical variables Symbol for displaying parameter values or connections Preparatory work Scaling intra-unit signals 11202 = Save MOT1 SET 518 = 500 V fixed! rated power converter voltageSet this only for units of the DCP 500 series 519 1305 = Field current for Under-excitation signal Presetting the field supply unit IV a 2 1201 = 3 Panel display ARM. Autotuning Adjusting the current controller DCS 500B / DCP 500B Operating Instructions IV a 2 Speed feedback balancing Only when the e.m.f. signal is being used as speed feedback Continue with Chapter Balancing the field supply unit and the e.m.f. controller Field weakening control with setting range 1 If the field time constant is not known 1204 = 1205 =11209 = 1009 = 1010 = 1201 = 0 Panel display not Activated 11202 = Save MOT1 SET1002 = 1004 = = decrease so that motor voltage is 40% 11003= decrease so that motor voltage is 70% Proceed as described in 1. / 2. / 3. above 12516 = increase slowly up to 20000 =100 % speed Only if analog tacho is used as speed feedback 1008 = desired response behaviour of controller 1708 = 0,1 s 1709 = 0,1 s1204 POT1 = 10%...20% max. speed 408 = desired response behaviour of controller 1204 = 1205 = Presetting the 3-phase field supply unit DCF 50xB 3603 = 1201 = 5Panel display FEX2/3 Autotuning3601 = 3602 = 1201 = 4Panel display ARM. MAN. Tuning ⇒ CDP ⇒ CDP 310 or CDP ID-NUMBER Total 1 Drives Start Mode Panel Functions ACT PAR Pin/Parameter Selecting and Changing of Value Drive Mode Value To enter the Parameter Mode Backupstoremode Saving of the Parameters to backup memory Display Mode Fault Resetting Reset Fault History Display DCS Uploading and Downloading of Parameters UPLOAD/DOWNLOAD DCS 500B / DCP 500B Operating Instructions IV a 3 Setting of the Display Contrast Full Name of output pinsDisplay Mode release key Selecting output pins Drive Mode Operational Com- mand Keys Running the Drive Mode Speed Reference Setting for the DriveTo enter the Reference Setting To exit the Reference Setting Display of status, alarm and fault signals Signals and Troubleshooting General messages Starting errors E Auxil. undervoltage Fault Signals F Conv.fan curr.fault Earth faultMotor 1 overtemp SDCS-IOB-3, SDCS-POW P418 Limited by the activation of a free wheeling Circuit Ext.Overvolt.FaultLocal & discon Nected Field ex.1 comerror Mains overvoltageCheck Parameters of Field Exciter Arm. curent ripple Field ex.1 not OK See Fault Code FNo ext. FAN ack No main cont. ack IV a 4 Current Difference Reversal Fault 101 Start inhibition Alarm Signals a103 Motor 1 temp. alarm Check See Fault Code F 105 Conv. overtemp 120 108110 118 130 127128 129 138 134136 137 At Macro x, macro-specific links or function 11201 Status Signals Backupstoremode Fexcstatus 11203 11205 11204 DCF 500B IV a a IV a a 055R0401A2440000