Fujitsu MBA3147RC, MBC2036RC, MBC2073RC, MBA3300RC, MBA3073RC specifications Sense Data

6.1 Sense Data

Table 6.4 Additional Sense Code and Additional Sense Code Qualifier (5/6)

C*	Q*	Name		Explanation	Sense
					key
44	nn	Internal target failure	An error was detected in self-diagnosis. ("nn" is a Fujitsu unique		4, B
			code)
			• 90:	Next sector HDD compare error
			• 91:	WCS RAM parity error
			• 92:	Unexpected FMT interrupt
			• 94:	NRZ parity error during Write (MAS3*** Series only)
			• 99:	Overflow error occurred at SPC FIFO
			• 9A:	Error interrupt in the HDC
			• A0:	Error interruption from DBM
			• A3:	DBM buffer CRC error
			• A4:	DBM internal parity error
			• A8:	Data late error	4, B
			• B0:	Flash ROM erase operation failed.	4
			• B1:	Flash ROM write operation failed.	4
			• C0:	RDCLK error (FMT hang up)	4
			• D1:	DSP downloading failed	4
			• D2:	DSP overrun (watch dog time out, DRV hard error)	4
			• D3:	Servo Gate Window error	4
			• D4:	Illegal error was reported from DSP	4
47	03	Information Unit iuCRC Error	An iuCRC error is detected on the SAS interface for a Data		B
		Detected	frame.
4B	01	Invalid Target Port Transfer	An illegal TPTT is received.		B
		Tag Received
	02	Too Much Write Data	The Write Data frame is longer than the stipulated frame length.		B
	03	ACK/NAK Timeout	A response to a XFER_RDY frame or Data frame has not been		B
			detected for more than 1 ms.
	04	NAK Received	A NAK primitive is received for a XFER_RDY frame or Data		B
			frame.
	05	Data Offset Error	A Relative Offset error is detected in a Write Data frame.		B
	06	Initiator Response Timeout	A response to a Data frame has not been detected for the		B
			"Initiator Response Timeout" in Mode Page 19.
4C	nn	Logical unit failed self-	The HDD's initial setup failed. ('nn' is a Fujitsu unique code)		4
		configuration	• 91:	Microcode Read error (any 3/11/** error during
				microcode read)
			• 93:	Microcode Read error (any 3/13/** NOSB error)
			• 94:	Microcode Read error (any 3/14/** NRF error)
			• 95:	Microcode Read error (any 3/15/** error during seek)
			• 97:	Microcode Read error (any 4/44/** or other errors
				during microcode read)
			• 98:	Invalid microcode (Header/Check Sum)
			• A1:	SA Read error (any 3/11/** error during SA read)
			• A3:	SA Read error (any 3/13/** error during SA read)
			• A4:	SA Read error (any 3/14/** error during SA read)
			• A5:	SA Read error (any 3/15/** error during SA read)
			• A7:	SA Read error (any 4/44/** error during SA read)
			• A8:	Invalid SA (Header/Check Sum)
			• AA:	SA Read error (DSP overrun/DRV hardware error)
			• AB:	SA Read error (abnormal rotation of spindle motor)
			• AC:	SA Read error (on-track failure)
			• E0:	Initial calibration failed
		* C: Additional Sense Code,		Q: Additional Sense Code Qualifier

C141-C013 369