Configuring the ATM Virtual Circuit | Garmin HM210DP/DI guide

Basic Configuration

5	Basic Configuration

This chapter provides basic configuration instructions to get your

HM210dp/di run and have your network connected to the Internet.

The instructions assume that the HM210dp/di is not predefined with any ATM VC, PPP or IpoA settings. For each connection method, example parameters are given for your better understanding. You should consult with your ISP to determine your connection mode and enter the actual values provided by your ISP.

NOTE! Your HM210dp/di may already be pre-configured with the necessary settings to get your network connected to the Internet. Contact your ISP to determine whether you should change any existing values.

5.1Configuring the ATM Virtual Circuit

As your LAN computers access the Internet via the HM210dp/di, data is exchanged with your ISP through a complex network of telephone switches, Internet routers, servers, and other specialized hardware. These various devices communicate using a common language, or protocol, called Asynchronous Transfer Mode (ATM). On the Wide Area Network (WAN) that connects you to your IPS, the ATM protocol performs functions like those that the Ethernet protocol performs on your LAN.

This section describes how to configure the ATM Virtual Circuit (VC). The VC properties define the path the HM210dp/di uses to communicate with your ISP over the ATM network.

5.1.1Adding ATM VCs

You may need to create a VC if none has been predefined on your system or if you use multiple services with your ISP. Each service may require its own VC.

Follow these instructions to add an ATM VC Interface:

1.Select ATM > ATM VC to display the ATM VC Configuration page.

2.Click the Add button to display the ATM VC – Add page:

EN/LZT 108 6492 R2 - October 2003

21

Image 29

Garmin HM210DP/DI manual Configuring the ATM Virtual Circuit, Adding ATM VCs

Contents

HM210dp/di Disclaimer CopyrightAbstract Trademark List Contents Configuring Dhcp Basic ConfigurationConfiguring IP Routes Configuring RIP Configuring NATConfiguring DNS Server Addresses Administration Tasks Configuring Firewall SettingsViewing DSL Line Information 101 Troubleshooting 104 Important Information 109 Glossary 118 Page Introduction FeaturesAbout this User Guide About the Adsl Modem HM210d Subscription for Adsl Service Package ContentsBefore You Start System Requirements Label Status/Description Front Panel and LED IndicatorsPhysical Appearance Choosing a Place for the Router Back Panel and Connectors Connecting the Hardware Windows 95, 98/98SE and Me Configuring PCs as Dhcp Clients192.168.1.1 255.255.255.0 Windows XP Windows Assigning Static IP Addresses to your PCs Windows Manager Accessing the Configuration Manager Functional Layout Commonly Used Buttons and Icons Button / Symbol Description Home Page and System View Table Table Heading Commiting Changes and Rebooting Setting Description Rebooting the HM210dp/di using Options Reboot from Minimum Configuration Quick Configuration Igmp Field Primary/Secondary DNS Server Adding ATM VCs Configuring the ATM Virtual CircuitSelect ATM ATM VC to display the ATM VC Configuration VC Interface VPI and VCI Mux Type Max Proto per AAL5 Modifying ATM VCs Adding PPP Interfaces Configuring PPP Interfaces Field Description Status Protocol Service Name Use Dhcp Use DNS Default Route Checking Your Connection Status Security Protocol Login Name Password Modifying and Deleteing PPP Interfaces Adding EoA Interfaces Configuring EoA Interfaces Field Description 0.0 Basic Configuration Select WAN IPoA to display the IPoA Configuration Configuring IPoA InterfacesAdding IPoA Interfaces Field Description Public / Private / DMZ Checking Your Connection Status Defining Bridge Interfaces Bridging Connection Mode Deleting a Bridge Interface Check Your Connection Status Overview of IP Routes Configuring IP Routes Viewing the IP Routing Table Field Select Routing IP Route Add. The IP Route Add page appears Adding IP Routes Overview of Dhcp Configuring DhcpDhcp Modes Dhcp Server Dhcp Client Configuring Dhcp ServerDhcp Relay Agent Creating Dhcp Server Address Pools Start IP Address End IP Address Mac Address Enabling Dhcp Server Mode Viewing, Modifying and Deleting Address Pools Configuring Your PCs as Dhcp Clients Viewing Current Dhcp Address Assignments Excluding IP Addresses from a Pool Defining the Dhcp Relay Interfaces Configuring Dhcp Relay Enabling Dhcp Relay Mode Configuring Your PCs as Dhcp Clients Overview of NAT Configuring NAT Configuration page appears Viewing NAT Configuration TCP Idle Timeoutsec TCP Close Waitsec Viewing NAT Rules and Rule Statistics Configuring NAT Application Level Gateway ALG , if any, that Viewing Current NAT Translations Field Description Napt Rule Adding NAT Rules RDR Rule Configuring NAT Basic Rule Configuring NAT Filter Rule Configuring NAT Enter a Destination Address From/To … Bimap Rule Configuring NAT Pass Rule Configuring NAT Assigning DNS Addresses Configuring DNS Server AddressesStatically Dynamically from a Dhcp pool Configured on the HM210dp/di Configuring DNS RelayOption 1 Using a PPP connection to learn the DNS Overview of DNS Relay Option 2 Configuring DNS on the HM210dp/di Go to Service DNS to display the DNS Configuration Overview of RIP Configuring RIP Select Services RIP and the RIP Configuration page appears Configuring the RIP Viewing RIP Statistics Configuring RIP Global Firewall Settings Configuring Firewall Settings Max Icmp Conn Conn Configuring IP Filters Viewing Your IP Filter Configuration Creating IP Filter Rules Configuring IP Filter Global Settings Configuring Firewall Settings Field Configuring Firewall Settings Configuring Firewall Settings IP Option Pkt Packet Size TOD Rule Status IP Filter Rule Examples Viewing IP Filter Statistics Managing Current IP Filter Sessions Blocking Specific Protocols Rarp Protocol Description IPX Bpdu Select Home Modify to display the System Modify Administration TasksChanging the System Date and Time Name Domain Name Configuring User Names and Passwords Administration Tasks Upgrading the Software Using Diagnostics Administration Tasks Accessing a Server with a Non-Standard Port Number Modifying Port Settings Viewing System Alarms Viewing DSL Line Information 102 103 14.1 LEDs TroubleshootingIndication/Symptom Troubleshooting Suggestion Internet Access How to use Winipcfg Configuration Manager ProgramDiagnosing Problem Using IP Utilities How to use Ipconfig How to use Ping Important Information Product Care and Maintenance License Agreement Limited WarrantyLicense Term Governing Law Intended UseLimitation of Liability Regulatory Information Safety ApprovalsEU Directives Declaration of Conformity 15.3.2.1 UL 1950 Statement EMC Approvals FCC Part 15 Statement FCC Part 68 Statement Telecom Approval Environmental Information Power SupplyFor EU For US HM210dp/di is intended for indoor public and private use Bridging AuthenticateGlossary Broadcast BroadbandDevice Dhcp Relay Downstream Domain nameEncapsulation Ethernet Gateway FirmwareDmt Lite Internet HostIntranet IP address NAT rule MAC address Port PacketPPPoE Protocol Subnet RemoteRouting Telnet T1.413 VPI and VCI Upstream