100
Guidelines Design and Specifications Thermal/Mechanical
4 | 3 | 2 |
|
| 1 |
| |
THIS DRAWING CONTAINS INTEL CORPORATION CONFIDENTIAL INFORMATION. IT IS DISCLOSED IN CONFIDENCE AND ITS CONTENTS |
|
| REVISION HISTORY |
|
| ||
ZONE | REV | DESCRIPTION | DATE | APPR | |||
MAY NOT BE DISCLOSED, REPRODUCED, DISPLAYED OR MODIFIED, WITHOUT THE PRIOR WRITTEN CONSENT OF INTEL CORPORATION. | |||||||
|
| 1 | A | INITIAL RELEASE | 07/15/08 | - | |
|
| 2 | B | UPDATE | 09/20/08 |
| |
|
| NOTES: |
|
|
|
| |
D | 5 | 1. THIS DRAWING TO BE USED IN CONJUNCTION WITH SUPPLIED 3D DATABASE. | D | ||||
ALL DIMENSIONS AND TOLERENCES ON THIS DRAWING TAKE PRECEDENCE OVER | |||||||
|
| SUPPLIED DATABASE |
|
| |||
|
| 2. PRIMARY DIMENSIONS STATED IN MILLINETERS. [BRACKETED] DIMESNIONS |
| ||||
|
| STATED IN INCHS. |
|
| |||
|
| 3 CRITICAL TO FUNCTION DIMENSION. |
|
| |||
| 1 | 4. REMOVE ALL BURRS, SHARP EDGES, GREASES, AND/OR SOLVENTS AFTER MACHINING | |||||
|
| AND FIN ASSEMBLY |
|
| |||
| 3 | 5 PART NUMBER AND TORGUE SPEC MARK: |
|
| |||
| PLACE PART NUMBER AND TORGUE SPEC IN ALLOWABLE AREA |
| |||||
| 4 | EITHER SIDE OF PART WHERE SHOWN. BELOW PART NUMBER CALLOUT, |
| ||||
|
| PLACE THE FOLLOW TEXT: |
|
| |||
|
| "RECOMMENDED SCREW TORQUE: 8 |
|
| |||
| 2 | THE MARK CAN BE AN INK MARK, LASER MARK, PUNCH MARK |
|
| |||
|
|
|
| ||||
|
| OR ANY OTHER PERMANENT MARK THAT IS READABLE AT 1.0X |
|
| |||
| 6 | MAGNIFICATION |
|
| |||
| 6. PRESS FIT CUP LIP FLUSH TO TOP SURFACE OF HEAT SINK |
|
| ||||
|
|
|
| ||||
|
| 7. MINIMUM PUSH OUT FORCE = 30LBF PER CUP |
|
| |||
5 |
|
|
|
|
| C | |
C |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| NO .DWG |
| 0.5 | +0.20 | 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| SECTION |
|
|
|
|
|
|
|
|
|
|
B | SEE DETAIL A |
| DETAIL A |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
|
|
| SCALE 4:1 |
|
|
|
|
|
| E49069 | |
|
| 1 | 6 |
| TIM, 0.25x35x35MM, HONEYWELL |
|
| ||||
|
|
|
|
|
| ||||||
|
| 4 | 5 | E50686 |
| SCREW, SHOULDER, M3X0.5, FOXHOLLOW |
|
| .SHT | ||
|
| 1 | 4 | E49059 |
| HEAT SINK, FOXHOLLOW, 1U |
|
| |||
|
|
|
|
|
| ||||||
|
| 4 | 3 | D91472 |
| CUP, SPRING RETENTION |
|
|
| 1 | |
|
| 4 | 2 | D89885 |
| RING, RETAINING, 3.2MM GROOVE DIA |
|
| REV | ||
|
|
|
|
|
| ||||||
|
| 4 | 1 | D89882 |
| SPRING, COMPRESSION, PRELOAD |
|
| B | ||
|
|
| TOP | E49069 |
| - |
|
|
|
|
|
A | A | QTY | ITEM NO | PART NUMBER |
|
| DESCRIPTION |
|
| ||
|
|
|
|
|
| ||||||
|
|
|
|
|
|
| PARTS LIST |
|
|
| |
|
| UNLESS OTHERWISE SPECIFIED |
| DESIGNED BY | DATE | DEPARTMENT |
| 2200 MISSION COLLEGE BLVD. |
| ||
|
| INTERPRET DIMENSIONS AND TOLERANCES | JUN LU | 07/15/08 |
|
| P.O. BOX 58119 |
| |||
|
| IN ACCORDANCE WITH ASME |
|
| |||||||
A |
|
| DIMENSIONS ARE IN INCHES |
| DRAWN BY | DATE |
| SANTA CLARA, CA | A | ||
|
| TOLERANCES: |
|
|
|
| |||||
|
| .X | 0.5 Angles | 1.0 | JUN LU | 07/15/08 | TITLE |
|
| ||
|
| .XX | 0.25 |
|
|
| |||||
|
|
| .XXX | 0.127 |
| CHECKED BY | DATE |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| THIRD ANGLE PROJECTION | - | - | ASSY, HEAT SINK, FOXHOLLOW, 1U | |||||
|
|
| - | - | |||||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| APPROVED BY | DATE | SIZE DRAWING NUMBER |
| REV | |
|
|
|
|
|
| - | - |
| |||
|
|
|
|
|
| C |
| E49069 | B | ||
|
|
|
|
|
| MATERIAL | FINISH |
| |||
|
|
|
|
|
| SEE NOTES | SEE NOTES | SCALE: 1:1 | DO NOT SCALE DRAWINGSHEET 1 OF 1 |
| |
4 | 3 |
|
|
|
| 2 |
|
|
| 1 |
|
Assembly Heatsink Collaboration
Drawings Mechanical