PREPARATIONS FOR OPERATION
Synchronizing with the Time Code of the IEEE1394
You can synchronize the time code when performing
Master unit |
|
|
| Slave unit |
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Screen Adjustment
LCD monitor direction, angle, screen brightness, etc. can be adjusted.
Adjusting the Direction and Angle of the LCD monitor
•With the LCD door in the open condition, rotate the LCD door.
•It can be turned 180° in upward direction and 90° in down- ward direction.
When turned 180° upward direction, the LCD monitor can be viewed from the lens side (vertically inverted image).
PEAKING volume
Viewfinder Adjustment
Direction of the Viewfinder
Adjust the position and angle of the viewfinder.
Diopter Adjustment
Rotate the eyepiece focusing ring until the viewfinder screen image is clearly visible.
Adjustment of the Viewfinder Screen
•PEAKING:
Adjusts the contour of the LCD monitor and the viewfinder screen.
•VF BRIGHT:
Adjusts the brightness of the viewfinder screen.
Eyepiece focusing ring
Slide the IEEE1394 | IEEE1394 terminal |
switch to the [DV] side. |
|
You can use the
Connections
Connect the master unit and the slave unit with an IEEE1394 cable.
Settings and Operations
• Master unit |
111 series) |
IEEE1394 terminal | Slide the IEEE1394 |
| switch to the [DV] side. |
IEEE1394 cable
Status display
DTCG 00 : 00 : 00 : 00
TC SLAVE LOCK ?
EXECUTE 
USER1
CANCEL USER3
180° up
LCD BRIGHT button
90° down
LCD lock release lever
VF BRIGHT volume
PEAKING volume
Sliding securing ring
Eyepiece
1.Set the IEEE1394 switch on the left side to [DV].
2.Set to Camera mode.
3.Set the recording format to
4.Set the TC GENE. switch to [FREE].
• Slave unit (GY-HD200U/GY-HD201E)
1.Set the IEEE1394 switch on the left side to [DV].
2.Set to VTR mode.
3.Check that the camera image from the master unit is input.
4.Set the TC GENE. switch to [FREE] and the TC DISPLAY switch to [TC].
5.Set to STOP mode or EJECT mode.
6.Press the STOP button for 1 second.
•The DV input time code data from the IEEE1394 termi- nal is displayed in the status display. (When status is in magnified size, characters are displayed.)
7.Press the USER1 button to begin slave lock.
(To skip slave lock, press the USER3 button and clear the status display.)
8.Check that the time code that is synchronized with the master unit is running.
9.Disconnect the IEEE1394 cable.
10.The slave unit finally returns to Camera mode.
MEMO
Slave lock cannot be performed in the following instances.
•Slave unit is in CAMERA mode
•Slave unit is in VTR mode and there is no DV signal
•The TC GENE. switch on the slave unit is not set to
FREE
•The slave unit is
•HDV format
If slave lock is performed in DV format and is then switched to HDV format, frame digit may deviate.
If power is turned off, slave lock is disabled. Perform slave lock operation again.
Slave lock cannot be performed for UB (User’s bit).
If the frame rate for the master unit and slave unit is not synchronized, it will not run properly. Synchronize frame rate before using.
If DROP/NON DROP is not synchronized, it will not run properly. Synchronize DROP/NON DROP before using.
Adjusting the LCD monitor
•PEAKING:
Adjusts the contour of the LCD monitor.
•LCD BRIGHT:
Adjusts the brightness of the LCD monitor.
Adjustments are made on the LCD/VF[2/4] menu screen. X See page 87.
•LCD MIRROR MODE:
Sets the LCD monitor to display mirrored images when shooting facing the subject.
Adjustments are made on the LCD/VF[4/4] menu screen. X See page 89.
•LCD CONTRAST:
Adjusts the contrast of the LCD monitor.
•BLACK & WHITE:
Sets the LCD monitor and viewfinder to black and white display.
Viewfinder mount base
Adjustments are made on the LCD/VF[4/4] menu screen. X See page 89.
•VF CONTRAST:
Adjusts the contrast of the viewfinder screen.
•BLACK & WHITE:
Sets the LCD monitor and viewfinder to black and white display.
MEMO
The screen size of the viewfinder can be changed by selecting the desired size with the ASPECT item on the VIDEO FORMAT[1/2] menu screen (4:3 or 16:9).
48 | 49 |
