INTRODUCTION
Battery Pack to be Used
This device can use any of the following batteries. (Factory setting)
U model: Anton Bauer battery
E model: IDX battery
Recommended batteries
U model: Dionic 90 (Anton Bauer)
E model:
For recording and storing videotapes in the best con- dition
Observe the following instructions for the best recording and storage of videotapes.
•Take care of the conditions of handling videotapes. It is recommended that you record and store videotapes in the environment below.
Storage |
Condensation
•If this device has been cooled down in a cold place and is then carried to a warm place, the moisture contained in the warm air may adhere to the head drum or tape guides and be cooled into water droplets. This phenomenon is referred to as condensation (dew). When this occurs, the head drum and tape guides are covered with droplets allowing the tape to be stuck to them, leading to tape dam- age.
eocassette, place this device in a tightly sealed vinyl bag, and then move it to a new environment.
To ensure no condensation occurs, allow the temperature of this device in the bag to reach that of the new environ- ment before using it.
Characteristic CCD Phe- nomena
Smear and Blooming
Due to the physical structure of a CCD it is possible to induce
CAUTION
Use only the recommended batteries.
If a heavy battery is used, the battery may fall out depend- ing on the way the HD camera recorder is used.
Videocassette to be Used
| Recording | Short period | Long period | |
| (Up to 10 | (Over 10 | ||
|
| |||
|
| years) | years) | |
Temperature | 17°C to 25°C | 15°C to 23°C | 15°C to 19°C | |
Humidity | 30% to 70% | 40% to 55% | 25% to 35% | |
Hourly tempera- | Less than | H | H | |
ture change | 10°C | |||
|
| |||
Hourly humidity | Less than | H | H | |
change | 10% | |||
|
|
•Condensation occurs in the following cases:
•When this device is suddenly moved from a cold place to a warm place.
•When a room heater has just 
started or when this device is exposed directly to cold air from an air conditioner.
•When this device is placed in a very humid place.
Head drum
Video tape
vertical streaking (called “smear”) when shooting an extremely bright light source. Another effect is the expansion of light around a bright light or object (called “blooming”).
The CCD employed in this device is characterized by induc- ing very little smear or blooming. Nevertheless, please take note that smear or blooming may be induced when shooting a bright light source.
Smear
Vertical pale streaking appearing at high luminous object
• Use JVC’s videocassette tapes marked with the A symbol.
• Mini DV videocassette :
*Do not use
•Videocassettes cannot be used upside down.
•Avoid storing a videocassette with its tape not being com- pletely wound, as this may damage the tape. Rewind it to the beginning before placing a cassette into storage.
•Store videocassettes in a place with little humidity and good ventilation where mould does not form.
•After a videocassette tape has been used repeatedly, it becomes unable to maintain full performance due to an increase in noise caused by dropouts, etc. Do not continue to use a dirty or damaged tape, as this will reduce the rotary head life.
•Videocassette tapes with the A symbol are provided with a switch on the back to prevent accidental erasure.
•Slide the switch to SAVE to protect the required recording in the tape from being overwritten.
•To record on the tape, slide the switch to REC.
•Do not leave the videotapes neglected for a long period. If videotapes are left wound for a long period of time, it may result in distortion of the tape. Also it may cause
•When tapes are not in use, store them in cases and on end. Storage cases protect videotapes from humidity, dust and ultraviolet light. Keep tapes in cases and do not store them lying flat. When housed in a horizontal position, pres- sure from other tapes can cause distortions and deforma- tions of the tape edges.
Do not leave the videocassette inserted when moving the camera under conditions where the temperature environ- ment changes.
After moving this device, do not use until the internal parts have stabilized.
•“CONDENSATION ON DRUM” is displayed on the LCD monitor and in the viewfinder when condensation occurs in this device.
Keep the power on until the warning message disappears. If the power is turned off while the warning message is dis- played, condensation may remain in the device even if the warning message is not displayed. Wait until this device is completely dry before using.
High luminous object (Electric light, sunlight, etc.)
|
|
| Blooming |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| Blurring in highlight |
Monitor screen |
| ||
Moire or Aliasing
Shooting stripes or fine patterns may cause a jagged effect or a banding in fine mesh patterns.
White dots
High temperatures can cause CCD sensor pixels to produce the effect of white dots in the image. This condition is con- spicuous especially when gain is applied.
This is a characteristic of the
Switch
•Pay attention to condensation even before the condensa- tion indication appears.
As condensation forms gradually, the condensation indica- tion may not appear for the first
In an extremely cold place, the condensation could freeze and turn into frost. In such a case, it takes an additional 2- 3 hours for the frost to first melt into condensation and then to be dissolved.
•To prevent condensation
When moving this device from one place to another where the temperatures are greatly deferent, first remove the vid-
8 | 9 |
