OTHERS
Warnings and Responses
Warnings are displayed on the LCD monitor or the viewfinder if there was a mistaken operation, if the battery or tape is low, or if there is a problem on the VTR.
In addition, if the tape or battery is low or the VTR has a problem, the tally lamp flashes (or lights) and an alarm is output from the monitor speaker or PHONES jack.
MEMO
This device uses microcomputers. It may not operate properly if there is external static or interference. If this happens, turn the power off and then on again.
Display | Status | Action |
60/30 INHIBIT | The FRAME RATE item is set to 50/25 or 24, and a tape re- | Sets the FRAME RATE item on the VIDEO FORMAT menu |
CHANGE FRAME | corded in 60/30 frame is played back or it is input into the | screen to match the frames. |
RATE MENU | IEEE1394 port in VTR mode. | X See page 74. |
50/25 INHIBIT | The FRAME RATE item is set to 60/30 or 24, and a tape re- |
|
CHANGE FRAME | corded in 50/25 frame or it is input into the IEEE1394 port |
|
RATE MENU | in VTR mode. |
|
24 INHIBIT CHANGE | The FRAME RATE item is set to 50/25 or 60/30, and a tape |
|
FRAME RATE MENU | recorded in 24 frame is played back or it is input into the |
|
| IEEE1394 port in VTR mode. |
|
| A tape recorded in | The E model cannot play back tapes recorded in |
| was played back or input into the IEEE1394 connector in | |
VTR mode on the E model. | nector in VTR mode. | |
| A tape recorded in | The U model cannot play back tapes recorded in |
| back or input into the IEEE1394 connector in VTR mode on | |
| the U model. | VTR mode. |
| A tape recorded in | This device cannot play back or input an |
INVALID! | input into IEEE1394 connector in VTR mode. | |
A tape recorded in |
| |
INVALID! | input into IEEE1394 connector in VTR mode. |
|
INVALID TAPE! | A computer data tape or a DVC PRO cassette was used. | Use a MiniDV videocassette. |
LP TAPE INVALID!* | Tried to play back a tape recorded in LP mode. | This device cannot record or play back in LP mode. |
NO DV SIGNAL* | DV signal was not input. | Set the IEEE1394 switch to DV and input a DV signal. |
NO HDV SIGNAL* | HDV signal was not input. | Set the IEEE1394 switch to HDV and input an HDV signal. |
COPY INHIBIT* | Tried to record a copyguarded signal. | Cannot record a copyguarded signal. |
REC INHIBIT* | A tape that cannot be recorded (back switch is set to SAVE) | Set the switch on the back of the cassette tape to REC. |
| was inserted. |
|
NO TAPE* | No videocassette tape is inserted. | Insert a cassette tape. |
Display | Status | Action |
CHANGE PB TAPE | Image format which is different from the one set in the PB | Check the setting for the PB TAPE item. |
FORMAT* | TAPE item on the VIDEO FORMAT[2/2] menu screen is be- | X See page 76. |
| ing played back. |
|
LOW VOLTAGE* | Battery is low. | Charge the battery pack or replace it. |
|
|
|
TAPE NEAR END* | There are less than 3 minutes remaining on the tape (flash- | To continue shooting, find a new tape or replace the tape. |
| es only when recording). |
|
TAPE END* | Displayed when the tape ends. | Replace the tape. |
|
|
|
CHANGE 1394 | Recording or playback video format and the IEEE1394 set- | Set the IEEE1394 switch correctly, turn the power off and |
SWITCH* | ting is different when connected to the IEEE1394 port. | then on again. |
SWITCH TO VTR | Tried to use the FF or REW button in camera mode. | Press the CAM/VTR button to set VTR mode. |
MODE* |
|
|
HEAD CLEANING | Displayed when the video head is dirty. (Head clogging was | Clean with a special head cleaning tape. |
REQUIRED | detected during an edit search in shooting mode as well as | X See page 7. |
| during playback and displayed.) |
|
CLEANING TAPE! | Displayed when a head cleaning tape is inserted. | The display disappears when the head cleaning tape is re- |
|
| moved. |
COPY GUARD!* | Tried to play back a copyguarded tape. | Cannot play back a copyguarded tape. |
FAN MOTOR HOUR | Over the prescribed fan motor usage time. | Please contact your local dealer or JVC. |
PUSH CASSETTE | The videocassette cover is not firmly shut. | Lightly push the top center of the videocassette cover. |
COVER* |
|
|
CHANGE THE SYS- | Displayed when you attempt to change FRAME RATE item | When the FRAME RATE item setting is changed, the frame |
TEM* | in the VIDEO FORMAT menu screen. | rate system for this device is changed. Check the frame |
|
| rate to use before changing the setting. |
|
| X See pages 53 and 74. |
*When status indications are magnified, warnings are not displayed on the LCD monitor. X See “Magnified Status Indications on the LCD Monitor” on page 29.
102 | 103 |
