JVC GY-HD200E/CHE, GY-HD200U/CHU manual Error Code Error Details GY-HD250/GY-HD251 Remedy Operation

OTHERS

Warnings and Responses (Cont’d)

Error code

Warning

•Warning Indications for VTR Abnormalities

Should malfunctions occur during VTR operation, this device self-diagnoses the cause and shows the diagnose together with an error code on the LCD monitor or in the viewfinder.

Error Code	Error Details	GY-HD250/GY-HD251	Remedy
		Operation
0201	Indicates dew formation (condensa-	Operation stops. All opera-	Leave this device with the power ON,
CONDENSATION ON DRUM	tion).	tions are rejected.	until the indication disappears.
3200	Tape cannot be loaded.		Switch the power OFF and then switch
LOADING FAILURE			it back ON. However, the tape may be
3300	Tape cannot be unloaded.		damaged depending on the circum-
UNLOADING FAILURE			stances. Please consult the person in
			charge of professional video equip-
4100	Irregularity with eject operation.
			ment at your nearest JVC-authorized
CASSETTE EJECT FAILURE
			service agent.
5605 - 5609	Tape is cut.	Operation stops.	Press the EJECT button to take out the
DEFECTIVE TAPE			cassette.
			If the tape runs out during recording,
			switch the power OFF and then switch
			it back ON, press the EJECT button,
			and then take out the cassette.
5702	Tape end sensor error.	Operation stops. All opera-	Switch the power OFF and then switch
TAPE END DET. ERROR		tions are rejected.	it back ON. However, the tape may be
5802	Tape beginning sensor error.		damaged depending on the circum-
TAPE BEGIN DET. ERROR			stances. Please consult the person in
			charge of professional video equip-
7001	Drum rotation error.
			ment at your nearest JVC-authorized
DRUM MOTOR FAILURE
			service agent.
7101	Capstan rotation error.
CAP MOTOR FAILURE
7202 - 7203	Supply reel rotation error.
SUPPLY REEL FAILURE
7302 - 7303	Take up reel rotation error.
TAKE UP REEL FAILURE
7305	Take up reel rotation error when un-
TAKE UP REEL FAILURE	loading.
8000	Tape problem detected.
EMERGENCY TAPE!
TURN POWER OFF.	System error when power is turned on.	HDV/DV LED, VTR indicator	Turn off the power and let this device
TURN BACK ON LATER.		and TALLY lamp flash. Only	sit for sometime before turning it back
		POWER switch operation is	on.
		accepted.

„TALLY lamp

Blinks when remaining battery power or tape is low. (Only in Camera mode)

Blinking Pattern	Remaining Battery/Tape
Slow blinking	• Remaining battery power is low.
(once per sec.)	• Remaining tape time is equivalent to less
	than 3 minutes.
Fast blinking	• Tape has run out.
(four times per sec.)	• Irregularity has occurred in the VTR.

„Alarm Sound

When remaining battery power becomes low, a warning sound is output from the monitoring loudspeaker and the PHONES jack.

(In Camera mode only)

When an irregularity occurs in the VTR, a warning sound is also output.

Whether or not alarm sound should be output and the vol- ume level are selected with the ALARM VR LEVEL item on the OTHERS[1/2] menu screen.

„Depending on the alarm conditions, the warning indicators on the LCD monitor/viewfinder screen, the TALLY lamp, and alarm sounds appear as shown in the following table.

Alarm Indications on LCD Monitor/			TALLY lamp	Alarm Sound	Condition
Viewfinder Screen
VTR alarm indication					Dew formation (condensation) or error has oc-
(Example)			I		curred in the VTR.
			J		About 3 min. before tape end
					(displayed during recording).
			I		Tape end
					(displayed during recording).
			J		Remaining battery power is low.
Display symbols	J	: Blinking once per second.		I	: Blinking four times per second.
		: Sound interrupted once per second.			: Continuous sound.

108 109