Korg KORG Pa50 user manual Param.4B Eq

	Low Cutoff [Hz]		20...1.0kHz
f	Sets the center frequency for Low EQ (shelving type)
	Gain [dB]		–18...+18dB
	Table , “Sets the gain of Low EQ,” on page 176
	Mid1 Cutoff [Hz]	300...10.00kHz
	Sets the center frequency for Mid/High EQ 1 (peaking type)
g	Q		0.5...10.0
	Sets the band width of Mid/High EQ 1		☞
	Gain [dB]		–18...+18dB
	Sets the gain of Mid/High EQ 1
	Mid2 Cutoff [Hz]	500...20.00kHz
	Sets the center frequency for Mid/High EQ 2 (peaking type)
h	Q		0.5...10.0
	Sets the band width of Mid/High EQ 2		☞
	Gain [dB]		–18...+18dB
	Sets the gain of Mid/High EQ 2
	Direct Mix	0...50
i	Sets the amount of the dry sound mixed to the distortion
	Speaker Simulation		Off, On
	Switches the speaker simulation on/off
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
j	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt		–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

a: Wah

The Wah parameter switches the wah effect on/off.

a: Sw

This parameter sets how the wah effect is switched on and off via the modulation source.

When “Sw” = Moment, the wah effect is usually turned off. It is turned on only when you press the pedal or oper- ate the joystick.

When a value for the modulation source is less than 64, “off” speed is selected, and when the value is 64 or higher, “on” is selected.

When “Sw” = Toggle, the wah effect is switched between on and off each time you press the pedal or operate the joystick.

The switch will be turned on/off each time the value of the modulation source exceeds 64.

b: Wah Sweep Range, b: Wah Sweep Src

This parameter sets the sweep range of the wah center frequency. A negative value will reverse the direction of sweep. The wah center frequency can be controlled by the modulation source specified in the “Wah Sweep Src” parameter.

d: Drive, e: Output Level

The degree of distortion is determined by the level of input signal and the setting of “Drive”. Raising the “Drive” setting will cause the entire volume level to increase. Use the “Output Level” parameter to adjust the volume level. The “Output Level” parameter uses the sig- nal level input to the 3-Band EQ. If clipping occurs at the 3-Band EQ, adjust the “Output Level” parameter.

d: Pre Low-cut

Cutting the signal in the low range before it is input to the Distortion will create a sharp distortion.

g: Q, h: Q

These parameters set the bandwidth of each equalizer. The higher the value, the narrower the band becomes.

Effects 179

Filter/Dynamic

007: Param.4B Eq

(Stereo Parametric 4-Band EQ)

This is a stereo 4-band parametric equalizer. You can select peaking type or shelving type for Band 1 and 4. The gain of Band 2 can be controlled by dynamic modulation.

Stereo In - Stereo Out
Left		Band3 Band4		Wet / Dry
Band1 Band2
PEQ	PEQ	PEQ	PEQ
Trim			HEQ
LEQ
LEQ			HEQ
Trim
PEQ	PEQ	PEQ	PEQ
Right				Wet / Dry
D-mod

a	Trim		0...100
	Sets the input level
b	Band1 Type	Peaking, Shelving-Low
	Selects the type of Band 1		☞
c	Band4 Type	Peaking, Shelving-High
	Selects the type of Band 4		☞
	Band2 Dynamic Gain Src		Off...Tempo
d	Selects the modulation source of the Band 2 gain			☞
	Amt [dB]		–18...+18dB
	Sets the modulation amount of Band 2 gain			☞
	Band1 Cutoff [Hz]		20...1.00kHz
	Sets the center frequency of Band 1
e	Q		0.5...10.0
	Sets the bandwidth of Band 1		☞ Fx:006
	Gain [dB]		–18.0...+18.0dB
	Sets the gain of Band 1
	Band2 Cutoff [Hz]		50...10.00kHz
	Sets the center frequency of Band 2
f	Q		0.5...10.0
	Sets the bandwidth of Band 2		☞ Fx:006
	Gain [dB]		–18.0...+18.0dB
	Sets the gain of Band 2		☞ ,
	Band3 Cutoff [Hz]		300...10.00kHz
	Sets the center frequency of Band 3
g	Q		0.5...10.0
	Sets the bandwidth of Band 3		☞ Fx:006
	Gain [dB]		–18.0...+18.0dB
	Sets the gain of Band 3
	Band4 Cutoff [Hz]		500...20.00kHz
	Sets the center frequency of Band 4
h	Q		0.5...10.0
	Sets the bandwidth of Band 4		☞ Fx:006
	Gain [dB]		–18.0...+18.0dB
	Sets the gain of Band 4
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
i	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt		–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

b: Band1 Type, c: Band4 Type

Selects a filter type for Band 1 and 4.

	Parametric 4EQ - Band1, Band4 Type
+Gain	3dB
	Band4 Type=Shelving High
	Band4 Type=Peaking
0dB
	Band1 Type=Shelving Low
–Gain	Band1 Type=Peaking
	3dB
	Band1 Cutoff	Band4 Cutoff