Korg KORG Pa50 user manual LCR BPM Dly, Stereo BPM Delay

049: LCR BPM Dly

The L/C/R delay enables you to match the delay time with the song tempo. You can also synchronize the delay time with the arpeggiator or sequencer. If you program the tempo before performance, you can achieve a delay effect that synchronizes with the song in real-time. Delay time is set by notes.

Note: With extreme values, the sync may be lost.

Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left				Wet / Dry
		Input Level D-mod	L Delay	Level
	+	High Damp Low Damp	C Delay	Spread
				Level
			Feedback
		Input Level D-mod	R Delay	Level
Right				Wet / Dry
Tempo
		BPM
BPM		Base Note x Times
		Base Note x Times
		Base Note x Times

a	BPM				MIDI, 40...240
	Selects MIDI Clock and assigns tempo				☞ ,
	L Delay Base Note
	Selects the type of notes to specify the delay time for TapL
b			☞ ,
	Times			x1...x16
	Sets the number of notes to specify the delay time for TapL					☞
	Level			0...50
	Sets the output level of TapL
	C Delay Base Note
	Selects the type of notes to specify the delay time for TapC
c			☞ ,
	Times			x1...x16
	Sets the number of notes to specify the delay time for TapC					☞
	Level			0...50
	Sets the output level of TapC
	R Delay Base Note
	Selects the type of notes to specify the delay time for TapR
d			☞ ,
	Times			x1...x16
	Sets the number of notes to specify the delay time for TapR					☞
	Level			0...50
	Sets the output level of TapR
	Feedback (C Delay)				–100...+100
	Sets the feedback amount of TapC
e	Src		Off...Tempo
	Selects the modulation source for the TapC feedback
	Amt		–100...+100
	Sets the modulation amount of the TapC feedback
	High Damp [%]			0...100%
f	Sets the damping amount in the high range					☞ Fx:043
	Low Damp [%]			0...100%
	Sets the damping amount in the low range					☞ Fx:043
	Input Level Dmod [%]		–100...+100
g	Sets the modulation amount of the input level	☞ Fx:037,
	Src					Off...Tempo
	Selects the modulation source for the input level					☞ Fx:037
h	Spread			0...50
	Sets the width of the stereo image of the effect sound		☞ Fx:043
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
i	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt				–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

Effects 207

ER/Delay

a:BPM, b: L Delay Base Note, b: Times, c: C Delay Base Note,

c:Times, d: R Delay Base Note, d: Times

The delay time is the length of the note obtained by mul- tiplying the “Base Note” parameter by the Times value, in relation to the tempo specified by the “BPM” parameter (or the MIDI Clock tempo if “BPM” is set to MIDI).

050: BPM Delay

(Stereo BPM Delay)

This stereo delay enables you to set the delay time to match the song tempo.

Note: With extreme values, the sync may be lost.

Stereo In - Stereo Out

Left Wet / Dry

		High Damp Low Damp
	Input Level D-mod	Delay
		Feedback
	Input Level D-mod	High Damp Low Damp
		Delay
Right		Wet / Dry
Tempo
	BPM	Adjust [%]
BPM	Base Note x Times
	Base Note x Times	Adjust [%]

	BPM	MIDI, 40...240
a	Selects MIDI Clock and assigns tempo	☞ Fx:049,
	R >		----, OVER!!
	Display the error message if the right channel delay time exceeds the upper
	limit				☞
	L Delay Base Note
	Selects the type of notes to specify the left channel delay time
		☞ Fx:049,
b	Times		x1...x16
	Sets the number of notes to specify the left channel delay time
			☞ Fx:049
	Adjust [%]		–2.50...+2.50%
	Fine-adjust the left channel delay time
	R Delay Base Note
	Selects the type of notes to specify the right channel delay time
		☞ Fx:049,
c	Times		x1...x16
	Sets the number of notes to specify the right channel delay time
					☞ Fx:049
	Adjust [%]		–2.50...+2.50%
	Fine-adjust the right channel delay time
	L Feedback			–100...+100
	Sets the feedback amount for the left channel
d	Src		Off...Tempo
	Selects the modulation source of feedback amount
	Amt L		–100...+100
	Sets the modulation amount of the left channel feedback
	R Feedback			–100...+100
e	Sets the feedback amount for the right channel
	Amt R		–100...+100
	Sets the modulation amount of the right channel feedback
f	High Damp [%]		0...100%
	Sets the damping amount in the high range				☞ Fx:043
g	Low Damp [%]		0...100%
	Sets the damping amount in the low range				☞ Fx:043
	Input Level Dmod [%]		–100...+100
h	Sets the modulation amount of the input level	☞ Fx:037,
	Src			Off...Tempo
	Selects the modulation source for the input level				☞ Fx:037
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
i	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175