Korg KORG Pa50 user manual Mixer FX Send A/B, Mixer FX Send C/D, MixerFXSend

76Song Play operating mode

Page 2 - Mixer: Pan

PAGE 2 - MIXER: PAN

Here you can adjust the pan for each Song track.

Use the TRACK SELECT button to switch between Song tracks 1-8, Song tracks 9-16, and back again.

Mixer:Pan

C+00 C+00

C+00 C+00

C+00 C+00

C+00 C+00

Mixer:Pan

C+00	C+00
C+00	C+00
C+00	C+00
C+00	C+00

Pan
-64	Hard Left.
+00	Center.
+63	Hard Right.
Off	The direct (uneffected) signal does not go to
	the outputs; only the FX signal is heard for this
	track.

PAGE 3 - MIXER: FX SEND A/B

This page lets you set the level of the track’s direct (unef- fected) signal going to the A and B Internal FX processors (usually assigned to Sequencer 1).

Use the TRACK SELECT button to switch from tracks 1-8 to tracks 9-16.

Mixer:FXSend

A:100 B:050 A:100 B:050

A:127 B:020 A:100 B:050

A:110 B:050 A:100 B:050

A:100 B:050 A:100 B:050

Mixer:FXSend

A:100 B:050 A:100 B:050

A:127 B:020 A:100 B:050

A:110 B:050 A:100 B:050

A:100 B:050 A:100 B:050

Note: When playing back a Song that makes use of all four effects (A-D), you can’t edit any effect parameter. These param- eters appear greyed out in the display.

Note: When you stop the Song, or select a different Song, the default effects are selected again. You can, however, stop the Song, change the effects, then start the Song again. Edit the Song in Song mode to permanently change the effects.

Here is the edit procedure:

1.Use the VOLUME/VALUE (A-H) buttons to select a track.

2.Use the F1-F4 buttons to select a parameter for that track.

3.Use the TEMPO/VALUE controls to change the parame- ter’s value.

Parameters

000No effect. Only the direct (uneffected) signal goes to the outputs.

127100% effect. The direct (uneffected) and effected signals go to the outputs with the same level.

PAGE 3 - MIXER: FX SEND C/D

This page lets you set the level of the track’s direct (unef- fected) signal going to the C and D Internal FX processors. Note: You can access this page only while editing the Sequencer 2, and the “S2 FX Mode” parameter is set to “CD Mode” (see page 80).

Use the TRACK SELECT button to switch from tracks 1-8 to tracks 9-16.

Mixer:FXSend

C:100 D:050 C:100 D:050

C:127 D:020 C:100 D:050

C:110 D:050 C:100 D:050

C:100 D:050 C:100 D:050

Mixer:FXSend

C:100 D:050 C:100 D:050

C:127 D:020 C:100 D:050

C:110 D:050 C:100 D:050

C:100 D:050 C:100 D:050

Here is the edit procedure:

1.Use the VOLUME/VALUE (A-H) buttons to select a track.

2.Use the F1-F4 buttons to select a parameter for that track.

3.Use the TEMPO/VALUE controls to change the parame- ter’s value.

Parameters

000No effect. Only the direct (uneffected) signal goes to the outputs.

127100% effect. The direct (uneffected) and effected signals go to the outputs with the same level.