Korg KORG Pa50 user manual 204, 045 M.Tap Delay Modul.Delay

204

Effects

ER/Delay

045: M.Tap Delay	046: Modul.Delay
(Stereo Multitap Delay)	(Stereo Modulation Delay)

The left and right Multitap Delays have two taps respectively.							This stereo delay uses an LFO to sweep the delay time. The
Changing the routing of feedback and tap output allows you							pitch also varies. You will obtain a delay sound with swell and
to create various patterns of complex effect sounds.							shimmering. You can also control the delay time using a
Stereo In - Stereo Out							modulation source.
Left						Wet / Dry	Stereo In - Stereo Out
		Feedback					Left
			Delay				Wet / Dry
				(2)
Input Level D-mod	High Damp Low Damp		(1)				Delay
				Mode	Spread	Tap1=(1)
	Mode	Tap1 Level
						Tap2=(2)
Input Level D-mod	High Damp Low Damp		(1)
				(2)			Feedback
			Delay
Right		Feedback					Delay
						Wet / Dry
							Right
							Wet / Dry

Mode: Normal Mode: Cross Feedback Mode: Cross Pan1 Mode: Cross Pan2 D-mod

D-mod	Response	L/R: +/+ +/–
LFO Sync	LFO: Tri / Sine	LFO Shape
		LFO
		LFO Phase	Modulation Mode

a	Mode	Normal, Cross Feedback, Cross Pan1, Cross Pan2
	Switches the left and right delay routing					☞
b	Tap1 Time [msec]			0.0...680.0msec
	Sets the Tap1 delay time
c	Tap2 Time [msec]			0.0...680.0msec
	Sets the Tap2 delay time
d	Tap1 Level			0...100
	Sets the Tap1 output level						☞
	Feedback (Tap2)				–100...+100
	Sets the Tap2 feedback amount
e	Src			Off...Tempo
	Selects the modulation source of the Tap2 feedback amount
	Amt			–100...+100
	Sets the modulation amount of the Tap2 feedback amount
f	High Damp [%]			0...100%
	Sets the damping amount in the high range					☞ Fx:043
g	Low Damp [%]			0...100%
	Sets the damping amount in the low range					☞ Fx:043
	Input Level Dmod [%]			–100...+100
h	Sets the modulation amount of the input level		☞ Fx:037,
	Src				Off...Tempo
	Selects the modulation source for the input level					☞ Fx:037
	Spread			–100...+100
	Sets the width of the stereo image of the effect sound
i			☞ Fx:043,
	Src			Off...Tempo
	Selects the modulation source of the effect sound’s stereo image width
	Amt			–100...+100
	Sets the modulation amount of the effect sound’s stereo image width
	Wet/Dry		Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
j	Src			Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt				–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

a: Mode

You can change how the left and right delay signals are panned by modifying the routing of the left and right delay as shown in the figure above. You need to input dif- ferent sounds to each channel in order for this parameter to be effective.

d: Tap1 Level

This parameter sets the output level of Tap1. Setting a dif- ferent level from Tap2 will add a unique touch to a monotonous delay and feedback.

a	Modulation Mode		LFO, D-mod
	Switches between LFO modulation control and modulation source control
	D-mod Modulation		L/R:+/+, L/R:+/–
	Reversed L/R control by modulation source				☞ ,
b	Src		Off...Tempo
	Selects the modulation source that controls delay time
	Response		0...30
	Sets the rate of response to the modulation source
	LFO Waveform		Triangle, Sine
c	Selects LFO Waveform
	LFO Shape		–100...+100
	Determines how much the LFO waveform is changed		☞ Fx:020
d	LFO Frequency [Hz]		0.02...20.00Hz
	Sets the LFO speed
	LFO Sync				Off, On
e	Switches LFO reset off/on				☞ ,
	Src		Off...Tempo
	Selects the modulation source that resets the LFO
	L LFO Phase [degree]		–180...+180
f	Sets the phase obtained when the left LFO is reset				☞
	R LFO Phase [degree]		–180...+180
	Sets the phase obtained when the right LFO is reset				☞
	L Depth		0...200
g	Sets the depth of the left LFO modulation
	R Depth		0...200
	Sets the depth of the right LFO modulation
	L Delay Time [msec]		0.0...500.0
h	Sets the left delay time
	R Delay Time [msec]		0.0...500.0
	Sets the right delay time
	L Feedback			–100...+100
i	Sets the feedback amount of left delay
	R Feedback			–100...+100
	Sets the feedback amount of right delay
	Wet/Dry	–Wet...–1:99, Dry, 1:99...Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
		☞ Fx:010,
j	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

b: D-mod Modulation

When the modulation source is used for control, this parameter reverses the left and right modulation direc- tion.

e:LFO Sync, e: Src,

f:L LFO Phase [degree], f: R LFO Phase [degree] The LFO can be reset via a modulation source.