Korg KORG Pa50 user manual 217, Lim-Phaser, Lim-MTapDly, Exc-Compr

072: Lim-Phaser

This effect combines a mono-type limiter and a phaser. You can change the order of the effect connection.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left				Wet / Dry
			Routing
	Limiter
			Phaser
+	Limiter		Phaser	Normal
	Gain Adjust		+
				Output Mode
			–
				Wet Invert
			Resonance
			Phaser Wet / Dry
Right				Wet / Dry
	Envelope - Control	LFO: Tri / Sine

	[L] Ratio	1.0:1...50.0:1, Inf:1
a	Sets the signal compression ratio		☞ Fx:003
	Threshold [dB]		–40...0dB
	Sets the level above which the compressor is applied		☞ Fx:003
	[L] Attack		1...100
b	Sets the attack time		☞ Fx:003
	Release		1...100
	Sets the release time		☞ Fx:003
c	[L] Gain Adjust [dB]		–Inf, –38...+24dB
	Sets the limiter output gain		☞ Fx:003
	[P] LFO Frequency [Hz]		0.02...20.00Hz
d	Sets the LFO speed
	LFO Waveform		Triangle, Sine
	Selects LFO Waveform
e	[P] Manual		0...100
	Sets the frequency to which the effect is applied
	[P] Depth		0...100
f	Sets the depth of LFO modulation
	Resonance		–100...+100
	Sets the resonance amount		☞ Fx:023
	[P] Phaser Wet/Dry	–Wet...–2:98, Dry, 2:98...Wet
g	Sets the phaser effect balance	☞ Fx:010, 023
	Output Mode	Normal, Wet Invert
	Selects the phaser output mode		☞ Fx:067
h	Routing	LMT→ PHS, PHS→ LMT
	Switches the order of the limiter and phaser connection		☞ Fx:067
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
i	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt		–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

073: Lim-MTapDly

(Limiter – Multitap Delay)

This effect combines a mono-type limiter and a multitap delay. You can change the order of the effect connection.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left		Routing	Wet / Dry
	Limiter	Multitap Delay
+		Feedback
	Limiter	Delay
	Gain Adjust	(2)
		High Damp(1)
		Mt.Dly Wet / Dry
Right			Wet / Dry
	Envelope - Control

	[L] Ratio	1.0:1...50.0:1, Inf:1
a	Sets the signal compression ratio		☞ Fx:003
	Threshold [dB]		–40...0dB
	Sets the level above which the compressor is applied		☞ Fx:003

			Effects		217
		Mono – Mono Chain
	[L] Attack				1...100
b	Sets the attack time			☞ Fx:003
	Release				1...100
	Sets the release time			☞ Fx:003
c	[L] Gain Adjust [dB]			–Inf, –38...+24dB
	Sets the limiter output gain			☞ Fx:003
	[D] Tap1 Time [msec]			0...680msec
d	Sets the Tap1 delay time
	Tap1 Level				0...100
	Sets the Tap1 output level			☞ Fx:045
	[D] Tap2 Time [msec]			0...680msec
e	Sets the Tap2 delay time
	Feedback (Tap2)			–100...+100
	Sets the Tap2 feedback amount
	[D] Mt.Delay Wet/Dry		Dry, 1:99...99:1, Wet
f	Sets the multitap delay effect balance
	High Damp [%]			0...100%
	Sets the damping amount in the high range			☞ Fx:043
g	Routing		LMT→ DLY, DLY→ LMT
	Switches the order of the limiter and multitap delay connection
	Wet/Dry		Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
h	Src			Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

074: Exc-Compr

(Exciter – Compressor)

This effect combines a mono-type exciter and a compressor. You can change the order of the effect connection.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left			Wet / Dry
		Routing
	Exciter	Compressor
+	EQ Trim LEQ HEQ
	Exciter	Comp
		Output Level
Right			Wet / Dry
		Envelope - Control

a	[X] Exciter Blend			–100...+100
	Sets the intensity (depth) of the Exciter effect			☞ Fx:011
b	[X] Emphatic Point			0...70
	Sets the frequency range to be emphasized			☞ Fx:011
c	[X] EQ Trim			0...100
	Table , “Sets the EQ input level,” on page 176
	[X] Pre LEQ Gain [dB]			–15...+15dB
d	Table , “Sets the gain of Low EQ,” on page 176
	Pre HEQ Gain [dB]			–15...+15dB
	Table , “Sets the gain of High EQ,” on page 176
e	[C] Sensitivity			1...100
	Sets the sensitivity			☞ Fx:002
	[C] Attack			1...100
f	Table , “Sets the attack level,” on page 176			☞ Fx:002
	Output Level			0...100
	Sets the compressor output level			☞ Fx:002
g	Routing	XCT→ CMP, CMP→ XCT
	Switches the order of the exciter and compressor connection
	Wet/Dry		Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
h	Src			Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175