Korg KORG Pa50 user manual Wah-AmpSim, Decim-Amp S, Decim-Cmp

222Effects

Mono – Mono Chain

083: Wah-AmpSim

(Wah/Auto Wah – Amp Simulation)

This effect combines a mono-type wah and an amp simula- tion. You can change the order of the effect connection.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left				Wet / Dry
			Routing
	Wah/Auto Wah
			Amp Simulation
+		Wah	Amp Simulation Filter
Right		Sweep Mode		Wet / Dry
	Envelope Auto
	D-mod	D-mod
		LFO
	LFO

	[W] Frequency Bottom			0...100
a	Sets the lower limit of the wah center frequency			☞ Fx:009
	Frequency Top			0...100
	Sets the upper limit of the wah center frequency			☞ Fx:009
	[W] Sweep Mode		Auto, D-mod, LFO
	Selects the control from auto-wah, modulation source, and LFO
b				☞ Fx:009,
	Src			Off...Tempo
	Selects the modulation source for the wah when Sweep Mode=D-mod
c	[W] LFO Frequency [Hz]			0.02...20.00Hz
	Sets the LFO speed
	[W] Resonance			0...100
d	Sets the resonance amount
	Low Pass Filter			Off, On
	Switches the wah low pass filter on and off
e	[A] Amplifier Type			SS, EL84, 6L6
	Selects the type of guitar amplifier
f	Routing	WAH →	AMP, AMP → WAH
	Switches the order of the wah and amp simulation connection
	Wet/Dry		Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
g	Src			Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

084: Decim-Amp S

(Decimator – Amp Simulation)

This effect combines a mono-type decimator and an amp simulation. You can change the order of the effect connec- tion.

	[D] Pre LPFOff, On
	Turn the harmonic noise caused by lowered sampling on and off
a		☞ Fx:014
	High Damp [%]	0...100%
	Sets the ratio of high-range damping
	[D] Sampling Freq [Hz] (Sampling Frequency)	1.00k...48.00kH
b	Sets the sampling frequency	z
	Resolution	4...24
	Sets the data bit length	☞ Fx:014
c	[D] Output Level	0...100
	Sets the decimator output level	☞ Fx:014
d	[A] Amplifier Type	SS, EL84, 6L6
	Selects the type of guitar amplifier
e	RoutingDECI→ AMP, AMP→ DECI
	Switches the order of the wah and amp simulation connection

Wet/DryDry, 1:99...99:1, Wet

Table , “Sets the balance between the effect and dry sounds,” on page 175

SrcOff...Tempo

fTable , “Selects the modulation source of the effect balance,” on page 175

Amt	–100...+100
Table , “Sets the modulation amount of the
effect balance,” on page 175

085: Decim-Cmp

(Decimator – Compressor)

This effect combines a mono-type decimator and a compres- sor. You can change the order of the effect connection.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left			Wet / Dry
		Routing
	Decimator		Compressor
Resolution		Output Level
+	Decimator		Comp
Pre LPF		High Damp	Output Level
Right			Wet / Dry
		Envelope - Control

	[D] Pre LPF			Off, On
	Turn the harmonic noise caused by lowered sampling on and off
a				☞ Fx:014
	High Damp [%]			0...100%
	Sets the ratio of high-range damping
	[D] Sampling Freq [Hz] (Sampling Frequency)			1.00k...48.00kHz
b	Sets the sampling frequency
	Resolution			4...24
	Sets the data bit length			☞ Fx:014
c	[D] Output Level			0...100
	Sets the decimator output level			☞ Fx:014
d	[C] Sensitivity			1...100
	Sets the sensitivity			☞ Fx:002
	[C] Attack			1...100
e	Table , “Sets the attack level,” on page 176			☞ Fx:002
	Output Level			0...100
	Sets the compressor output level			☞ Fx:002
f	Routing	DECI→	CMP, CMP→ DECI
	Switches the order of the decimator and compressor connection