Korg KORG Pa50 user manual 043 L/C/R Delay, Cross Delay, High Damp %, e Low Damp %, Spread

c: Envelope Select, c: Src, d: Threshold

These parameters select the source to control the start and end of recording.

When “Envelope Select” is set to D-mod, the input signal will be recorded only when the value of the modulation source selected by the Src parameter is 64 or higher.

When “Envelope Select” is set to Input, the input signal will be recorded only when its level exceeds the Threshold level.

When recording is completed, reverse playback starts immediately.

043: L/C/R Delay

This multitap delay outputs three Tap signals to the left, right, and center respectively. You can also adjust the left and right spread of the delay sound.

Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left		Wet / Dry
Input Level D-mod	L Delay
		Level
+	C Delay	Spread
High Damp Low Damp		Level
	Feedback
Input Level D-mod	R Delay	Level
Right		Wet / Dry

	L Delay Time [msec]			0...1360msec
a	Sets the delay time of TapL
	Level		0...50
	Sets the output level of TapL
	C Delay Time [msec]			0...1360msec
b	Sets the delay time of TapC
	Level		0...50
	Sets the output level of TapC
	R Delay Time [msec]			0...1360msec
c	Sets the delay time of TapR
	Level		0...50
	Sets the output level of TapR
	Feedback (C Delay)			–100...+100
	Sets the feedback amountof TapC
d	Src		Off...Tempo
	Selects the modulation source of the TapC feedback amount
	Amt		–100...+100
	Sets the modulation amount of the TapC feedback amount
	High Damp [%]		0...100%
e	Sets the damping amount in the high range					☞
	Low Damp [%]		0...100%
	Sets the damping amount in the low range					☞
	Input Level Dmod [%]		–100...+100
f	Sets the modulation amount of the input level	☞ Fx:037,
	Src			Off...Tempo
	Selects the modulation source for the input level				☞ Fx:037
g	Spread		0...50
	Sets the width of the stereo image of the effect sound				☞
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
h	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

Effects 203

ER/Delay

e: High Damp [%], e: Low Damp [%]

These parameters set the damping amount of high range and low range. The tone of the delayed sound becomes darker and lighter as it feeds back.

g: Spread

This parameter sets the pan width of the effect sound. The stereo image is widest with a value of 50, and the effect sound of both channels is output from the center with a value of 0.

044: Cross Delay

(Stereo/Cross Delay)

This is a stereo delay, and can by used as a cross-feedback delay effect in which the delay sounds cross over between the left and right by changing the feedback routing.

Stereo In - Stereo Out
Left		Wet / Dry
	High Damp	Low Damp
Input Level D-mod	Delay
Stereo/Cross	Feedback	Spread
Input Level D-mod	High Damp	Low Damp
	Delay	Stereo/Cross
Right		Wet / Dry

a	Stereo/Cross		Stereo, Cross
	Switches between stereo delay and cross-feedback delay
b	L Delay Time [msec]		0.0...680.0msec
	Sets the delay time for the left channel
c	R Delay Time [msec]		0.0...680.0msec
	Sets the delay time for the right channel
	L Feedback			–100...+100
	Sets the feedback amount for the left channel
d	Src		Off...Tempo
	Selects the modulation source of feedback amount
	Amt L		–100...+100
	Sets the modulation amount of the left channel feedback
	R Feedback			–100...+100
e	Sets the feedback amount for the right channel
	Amt R		–100...+100
	Sets the modulation amount of the right channel feedback
f	High Damp [%]		0...100%
	Sets the damping amount in the high range				☞ Fx:043
g	Low Damp [%]		0...100%
	Sets the damping amount in the low range				☞ Fx:043
	Input Level Dmod [%]		–100...+100
h	Sets the modulation amount of the input level	☞ Fx:037,
	Src			Off...Tempo
	Selects the modulation source for the input level				☞ Fx:037
i	Spread		–50...+50
	Sets the width of the stereo image of the effect sound		☞ Fx:043
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
j	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175