Maximum positive/negative pitchbend range (in semitones). 12 = ±1 octave.
No pitchbend allowed.

PAGE 6 - TUNING: SCALE

This page lets you program the alternative scale for the Song tracks.

Tuning:Scale

Scale:User

Key:C

Note:C#

Detune:+63

Scale

Alternative scale for the Song tracks. See “Scales” on page 227 for a list of available scales. To enable/disable the alternative scale for each Song track, see “Page 7 - Tuning: PitchBend/ Scale” on page 97.

Key

Parameter required for some Scales, when you should set a preferred key.

Note

Note in edit, to be detuned. This parameter can be accessed when a User Scale is selected.

Detune

Note detune, compared to the standard Equal tuning. This parameter can be accessed when a User Scale is selected.

PAGE 7 - TUNING: PITCHBEND/SCALE

This page lets you program the Pitch Bend range for the Song tracks. Furthermore, it lets you activate/deactivate the alter- native scale for each track.

Use the TRACK SELECT button to switch between Song tracks 1-8, Song tracks 9-16, and back again.

Tuning:PB/Scale

PB:02 Sc:N PB:02 Sc:N

PB:02 Sc:N PB:02 Sc:N

PB:02 Sc:N PB:02 Sc:N

PB:02 Sc:N PB:02 Sc:N

Tuning:PB/Scale

PB:02 Sc:N PB:02 Sc:N

PB:02 Sc:N PB:02 Sc:N

PB:02 Sc:N PB:02 Sc:N

PB:02 Sc:N PB:02 Sc:N

PB(end)

This parameters shows the Pitch Bend range for each track, in semitones.

01…12

Off

Song operating mode 97

Page 6 - Tuning: Scale

Sc(ale)

This parameter lets you activate/deactivate the alternative scale for each track. (See “Page 6 - Tuning: Scale” on page 97 for more information on selecting an alternative scale).

Yes

The track is tuned according to the alternative

 

scale.

No

The track is tuned according to the Global

 

scale (see “Scale” on page 125).

PAGE 8 - FX: A/B SELECT

This page lets you select the A and B effects. Usually, the A effect is a reverb, while the B effect is a modulating effect. Standard MIDI Files usually require two effects only. You can, however, assign all four effects to a Song (see “Page 3 - Mixer: FX Block” on page 96).

FX:A/B Select

A:02 B:89

Compressor Rev-Gate

ModTrk:Up1 B>Asend:127

Note: When you stop the Song, or select a different Song, the default effects are selected again. You can, however, stop the Song, change the effects, then start the Song again. Save the Song to permanently change the effects.

A, B

Effects assigned to the A and B effect processors. Usually, A is the reverb, while B is the modulating effect (chorus, flanger, delay…). For a list of the available effects, see “Effects” on page 175.

ModTrk (Modulating Track)

Source track for modulating MIDI messages. You can modu- late an effect parameter with a MIDI message generated by a physical controller.

B>Asend (B>A Send)

Amount of the B effect going back to the input of the A effect.

PAGE 9 - FX: C/D SELECT

This page lets you select the C and D effects. Usually, the C effect is a reverb, while the D effect is a modulating effect. Standard MIDI Files usually require two effects only. You can, however, assign all four effects to a Song (see “Page 3 - Mixer: FX Block” on page 96).

FX:C/D Select

C:02 D:89

Compressor Rev-Gate

ModTrk:Up1 D>Csend:127

Note: When you stop the Song, or select a different Song, the default effects are selected again. You can, however, stop the

Page 99
Image 99
Korg KORG Pa50 user manual Tuning Scale, Tuning PITCHBEND/SCALE, FX A/B Select, FX C/D Select, TuningPB/Scale