212 Effects
Mono – Mono Chain

062: P4Eq-TapDly

(Parametric 4-Band EQ – Multitap Delay)
This effect combines a mono-type four-band parametric

equalizer and a multitap delay.

063: Cmp-AutoWah

(Compressor – Wah/Auto Wah)

This effect combines a mono-type compressor and a wah.

You can change the order of the connection.

a[E] Trim
Sets the parametric EQ input level 0...100
b
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1 20...1.00kHz
Q
Sets the bandwidth of Band 1 0.5...10.0
☞ Fx:006
Gain [dB]
Sets the gain of Band 1 –18...+18dB
c
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2 50...5.00kHz
Q
Sets the bandwidth of Band 2 0.5...10.0
☞ Fx:006
Gain [dB]
Sets the gain of Band 2 –18...+18dB
d
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3 300...10.00kHz
Q
Sets the bandwidth of Band 3 0.5...10.0
☞ Fx:006
Gain [dB]
Sets the gain of Band 3 –18...+18dB
e
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4 500...20.00kHz
Q
Sets the bandwidth of Band 4 0.5...10.0
☞ Fx:006
Gain [dB]
Sets the gain of Band 4 –18...+18dB
f
[D] Tap1 Time [msec]
Sets the Tap1 delay time 0...680msec
Tap1 Level
Sets the Tap1 output level 0...100
☞ Fx:045
g
[D] Tap2 Time [msec]
Sets the Tap2 delay time 0...680msec
Feedback
Sets the Tap2 feedback amount –100...+100
h
[D] Mt.Delay Wet/DryDry, 2:98...98:2, Wet
Sets the multitap delay effect balance
High Damp [%]
Sets the damping amount in the high range 0...100%
☞ Fx:043
i
Wet/DryDry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on
page 175
SrcOff...Tempo
Table , “Selects the modulation source of the effect balance,” on
page 175
Amt
Table , “Sets the modulation amount of the
effect balance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Trim
+
Parametric 4Band EQ Multitap Delay
Feedback
High Damp
Delay
(2)
(1) Mt.Dly Wet / Dry
a[C] Sensitivity
Sets the sensitivity 1...100
☞ Fx:002
b
[C] Attack
Table , “Sets the attack level,” on page 176 1...100
☞ Fx:002
Output Level
Sets the compressor output level 0...100
☞ Fx:002
c[C] EQ Trim
Table , “Sets the EQ input level,” on page 176 0...100
d
[C] Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176 –15...+15dB
Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176 –15...+15dB
e
[W] Frequency Bottom
Sets the lower limit of the wah center frequency 0...100
☞ Fx:009
Frequency Top
Sets the upper limit of the wah center frequency 0...100
☞ Fx:009
f
[W] Sweep Mode Auto, D-mod, LFO
Selects the control from auto-wah, modulation source, and LFO
☞ Fx:009,
Src Off...Tempo
Selects the modulation source for the wah when Sweep Mode=D-mod
g[W] LFO Frequency [Hz]
Sets the LFO speed 0.02...20.00Hz
h
[W] Resonance
Sets the resonance amount 0...100
Low Pass Filter
Switches the wah low pass filter on and off Off, On
iRouting CMP → WAH, WAH → CMP
Switches the order of the compressor and wah connection
j
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Compressor
Routing
Wah/Auto Wah
Wah
D-mod
Envelope
Sweep Mode
D-mod
Auto
LFO
LFO
LEQ HEQ
EQ Trim
Comp
Output Level
Envelope - Control