Korg KORG Pa50 user manual Phser-ChoFl, Rev-Gate, Phaser Chorus/Flanger, Reverb Gate

224Effects

Mono – Mono Chain

088: Phser-ChoFl

(Phaser – Chorus/Flanger)

This effect combines a mono-type phaser and a chorus/ flanger.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left					Wet / Dry
	Phaser		Chorus/Flanger
+	Phaser	EQ	Chorus/Flanger		Normal
			LEQ HEQ	+
		Trim			Output Mode
	Resonance	Phaser	Feedback	–	Wet Invert
		Wet / Dry
				Cho/Flng
Right				Wet / Dry
					Wet / Dry
LFO: Tri / Sine			LFO: Tri / Sine

	[P] LFO Frequency [Hz]			0.02...20.00Hz
a	Sets the LFO speed
	LFO Waveform			Triangle, Sine
	Selects LFO Waveform
	[P] Manual			0...100
	Sets the frequency to which the effect is applied
b	Depth			0...100
	Sets the depth of LFO modulation
	Resonance			–100...+100
	Sets the resonance amount			☞ Fx:023
c	[P] Phaser Wet/Dry	–Wet...–2:98, Dry, 2:98...Wet
	Sets the phaser effect balance		☞ Fx:010, 023
	[F] LFO Frequency [Hz]			0.02...20.00Hz
d	Sets the LFO speed
	LFO Waveform			Triangle, Sine
	Selects LFO Waveform
	[F] Delay Time [msec]			0.0...50.0msec
	Sets the delay time
e	Depth			0...100
	Sets the depth of LFO modulation
	Feedback			–100...+100
	Sets the feedback amount			☞ Fx:020
f	[F] EQ Trim			0...100
	Table , “Sets the EQ input level,” on page 176
	[F] Pre LEQ Gain [dB]			–15...+15dB
g	Table , “Sets the gain of Low EQ,” on page 176
	Pre HEQ Gain [dB]			–15...+15dB
	Table , “Sets the gain of High EQ,” on page 176
	[F] Cho/Flng Wet/Dry	–Wet...–2:98, Dry, 2:98...Wet
h	Sets the effect balance of the chorus/flanger		☞ Fx:010, 020
	Output Mode		Normal, Wet Invert
	Selects the output mode for the chorus/flanger			☞ Fx:060
	Wet/Dry		Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
i	Src			Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

089: Rev-Gate

(Reverb – Gate)

This effect combines a mono-type reverb and a gate.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
	Reverb	Wet / Dry

		EQ Trim
+	Pre Delay		Reverb	Gate
		LEQ HEQ		Reverb
				Balance
Right				Wet / Dry
			Input Reverb Mix
			Input
	Gate+Dmpr		Envelope - Control
			D-modEnvelope Select	Gate

	[R] Reverb Time [sec]		0.1...10.0sec
a	Sets the reverberation time
	High Damp [%]		0...100%
	Sets the damping amount in the high range
b	[R] Pre Delay [msec]		0...200msec
	Sets the delay time of the reverb sound and gate control signal
c	[R] EQ Trim		0...100
	Table , “Sets the EQ input level,” on page 176
	[R] Pre LEQ Gain [dB]		–15...+15dB
d	Table , “Sets the gain of Low EQ,” on page 176
	Pre HEQ Gain [dB]		–15...+15dB
	Table , “Sets the gain of High EQ,” on page 176
e	[R] Reverb Balance	Dry, 1:99...99:1, Wet
	Sets the reverb effect balance
	[G] Envelope Select		D-mod, Input
	Switches between modulation source control and input signal control
f			☞
	Src	Off...Gate2+Dmpr
	Selects the modulation source that controls the gate when Envelope Select
	is set to D-mod		☞
	[G] Input Reverb Mix	Dry, 1:99...99:1, Wet
	Sets the balance between the dry and reverb sounds of the gate control sig-
g	nal.		☞
	Threshold		0...100
	Sets the gate threshold level		☞
	[G] Polarity		+, –
h	Switches between non-invert and invert of the gate on/off state
			☞ Fx:005
	[G] Attack		1...100
i	Sets the attack time		☞ Fx:005
	Release		1...100
	Sets the release time		☞ Fx:005
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
j	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt		–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

f:Envelope Select, f: Src, g: Input Reverb Mix, g: Threshold The “Envelope Select” parameter enables you to select whether turning the gate on and off is triggered by the input signal level or controlled directly by the modulation source. You can select from Off to Gate2+Dmpr for the Src parameter to specify the modulation source.

When “Envelope Select” is set to Input, the gate is con- trolled by the level of signals that are the combination of the dry sound and the reverb sound. When the signal level exceeds the threshold, the gate opens and the reverb sound is output.

Normally, set “Input Reverb Mix” to Dry (the gate is con- trolled only by the dry sound). If you wish to extend the gate time, set the “Input Reverb Mix” value higher and adjust the “Threshold” value.