Korg KORG Pa50 user manual DK Samples

108Program operating mode

Page 2 - DK Samples (Drum Programs)

Velocity Switch

This is the velocity value dividing the High and Low layers for the selected oscillator. Notes struck harder than this value will be played by the High multisample.

V-Zone Top/Bottom (Velocity Zone)

Here you can specify the velocity range for the selected oscil- lator.

Note: You cannot set the Bottom Velocity higher than the Top Velocity, nor the Top Velocity lower than the Bottom Velocity.

0…127 Assigned velocity.

Octave

Use this parameter to adjust the pitch of the selected oscilla- tor in octave units. The normal octave of the multisample is “0”.

-2…+1 Octave transposition.

Transpose

Use this parameter to adjust the pitch of the selected oscilla- tor in semitone steps over a range of ±1 octave.

-12…+12 Transposition in semitones.

Tune

Use this parameter to adjust the pitch of the sample in one- cent steps (a semitone is 100 cents) over a range of ±1 octave. -1200…+1200

Fine-tune value in cents.

Delay (ms)

This parameter sets a delay time from the note-on to the real beginning of the sound. With a setting of KeyOff, the sound will begin when note-off occurs. This is useful to create sounds such as the “click” that is heard when a harpsichord note is released. In this case, set the “Sustain Level” parame- ter to 0 (see page 14-115).

Key Off The sound will begin when the note is released.

0…5000 Delay time in milliseconds.

PAGE 2 - DK SAMPLES (DRUM PROGRAMS)

This page appears when you edit a Drum Program. Here you can select a different percussive sample for each layer (High and Low) on each key.

DK Samples

Key:	C 2
Assigned:	Yes
MS Hi Bank/Num:	ROM
BD-SoftRoom	4

Key

Key in edit. You can press a key on the keyboard to select a key.

Assigned

Use this parameter to turn the sample on/off.

Yes	The sample is assigned to the selected key.
No	The sample is not assigned. The sample
	assigned to the next highest assigned key is
	used instead.

MS Hi/Lo Bank/Num

Use these parameters to select a different multisample (drum kit) for each of the High and Low layers. For more informa- tion, see “MS Hi/Lo Bank/Num” on page 107.

[H/L] Level

These parameters specify the level of each multisample. For more information, see “[H/L] Level” on page 107.

[H/L] Transpose

These parameters transpose the selected multisample. Use them to change the pitch of the selected key.

0No transposition applied.

-64…+63 Transpose value in semitones.

[H/L] Tune

Use these parameters to fine-tune the assigned sample.

0	No fine-tuning.
-99…+99	Fine-tuning value in cents (1/100 of a semi-
	tone).

[H/L] Reverse

The multisample will be played in reverse. For more informa- tion see “[H/L] Reverse” on page 107.

[H/L] Use Offset

These parameters specify the point where the multisample(s) will begin to play. For more information see “[H/L] Use Off- set” on page 107.

[H/L] Cutoff

These parameters set the cutoff frequency for the filter applied to the selected sample.

[H/L] Resonance

These parameters set the resonance for the filter applied to the selected sample.

[H/L] Attack

These parameters are an offset to the selected sample’s EG Attack.

[H/L] Decay

These parameters are an offset to the selected sample’s EG Decay.

Velocity Switch

This is the velocity value dividing the High and Low layers for the selected sample/key. Notes stricken harder than this value will be played by the High multisample.

Single Trigger

Use this parameter to set the sample as a single-triggered one.

Yes	When the same key (note) is played repeatedly,
	the previous note will be stopped before the
	new note is triggered, so that they will not
	overlap.
No	When the same key (note) is played repeatedly,
	the previous note will not be stopped before
	the new note is triggered.

Receive Note On

Use this parameter to enable/disable the reception of the Note On (Key On) message.

Yes	The Note On message is normally received.
No	The Note On message is not received. There-
	fore, the corresponding key is muted.