Korg KORG Pa50 user manual AutoFadeMod, 029 2Voice Res, Stereo Auto Fade Modulation

192Effects

Pitch/Phase Mod.

The following is an example of fade-in where the LFO speed is increased from “1.0Hz” to “4.0Hz” when a note- on message is received.

“AUTOFADE Src”=Gate1, “LFO Frequency [Hz]”=1.0 “LFO Frequency Mod”=AUTOFADE, “Amt”=3.0

The effect is off when a value for the dynamic modulation source specified for the “AUTOFADE Src” parameter is smaller than 64, and the effect is on when the value is 64 or higher. The AutoFade function is triggered when the value changes from 63 or smaller to 64 or higher.

AUTOFADE AutoFade

AUTOFADE Src=Gate1

LFO Frequency[Hz]=1.0

Gate1 SignalLFO Freq. Mod=AUTOFADE

Amt=+3.0

	Note On		All Note Off
		Fade-In Rate		LFO Frequency
AUTOFADE				=1.0+3.0=4.0Hz
	Fade-In Dealy
				LFO Frequency
				=1.0Hz

028: AutoFadeMod.

(Stereo Auto Fade Modulation)

This stereo chorus/flanger effect enables you to control the LFO speed and effect balance using auto fade, and you can spread the sound by offsetting the phase of the left and right LFOs from each other.

Stereo In - Stereo Out
Left	Wet / Dry
	Delay
	Feedback
	High Damp
	Delay
Right	Wet / Dry
	LFO Phase
LFO: Tri / Sine	LFO Shape
AutoFade	LFO Frequency
	Wet / Dry

	AUTOFADE Src		Off...Tempo
	Selects the modulation source that starts AutoFade		☞ Fx:027,
a
	Rate		1...100
	Sets the rate of fade-in		☞ Fx:027
	Fade-In Dly (Fade-In Delay) [msec]		00...2000msec
	Sets the fade-in delay time		☞ Fx:027
	LFO Waveform		Triangle, Sine
b	Selects LFO Waveform
	LFO Shape		–100...+100
	Determines how much the LFO waveform is changed		☞ Fx:020
c	LFO Phase [degree]		–180...+180
	Sets the LFO phase difference between the left and right		☞ Fx:010
	LFO Frequency Mod	D-mod, AUTOFADE
d	Switches between D-mod and AUTOFADE for the LFO frequency modula-
	tion		☞ Fx:027
	LFO Frequency [Hz]		0.02...20.00Hz
	Sets the LFO speed
e	Src		Off...Tempo
	Selects the modulation source of LFO speed
	Amt	–20.00...+20.00Hz
	Sets the modulation amount of LFO speed
	L Delay Time [msec]		0.0...500.0msec
f	Sets the left channel delay time
	R Delay Time [msec]		0.0...500.0msec
	Sets the right channel delay time
g	Depth		0...200
	Sets the depth of LFO modulation
	Feedback		–100...+100
h	Sets the feedback amount		☞ Fx:020
	High Damp [%]		0...100%
	Sets the feedback damping amount in the high range		☞ Fx:020

Wet/Dry Mod D-mod, AUTOFADE

iSwitches between D-mod and AUTOFADE for the effect balance modulation ☞ Fx:027

	Wet/Dry	–Wet...–1:99, Dry, 1:99...Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
		☞ Fx:010, 020,
j	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

029: 2Voice Res

This effect resonates the input signal at a specified pitch. You can set the pitch, output level, and pan settings for two reso- nators individually. You can control the resonance intensity via an LFO.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left			Wet / Dry
	High Damp
Trim	Resonator	Level	Pan
+	Resonance
Trim	Resonator	Level	Pan
	High Damp
Right			Wet / Dry
D-mod	Invert: On/Off
LFO	Pitch, Fine [cent]
	Control Mode
Manual

	Control Mode	Manual, LFO, D-mod
a	Switches the controls of resonance intensity		☞ ,
	LFO/D-mod Invert		Off, On
	Reverses the Voice 1 and 2 control when LFO/D-mod is selected			☞
	LFO Frequency [Hz]		0.02...20.00Hz
b	Sets the LFO speed
	D-mod Src		Off...Tempo
	Selects the modulation source that controls resonance intensity
	Mod. Depth		–100...+100
c	Sets the amount of resonance intensity control via LFO/D-mod
	Trim			0...100
	Sets the input level at the resonator
	Voice1: Pitch				C0...B8
d	Sets the voice1 Pitch for resonance
	Fine [cent]		–50...+50
	Fine-adjusts the voice 1 pitch for resonance
	Voice1: Resonance		–100...+100
e	Sets the intensity of resonance when Control Mode = Manual			☞
	High Damp [%]	0...100%
	Sets the damping amount of resonant sound in the high range			☞
	Voice1: Level			0...100
f	Sets the Voice1 output level
	Pan				L6...R6
	Sets the Voice1 stereo image
	Voice2: Pitch				C0...B8
g	Sets the Voice2 Pitch for resonance
	Fine [cent]			–50...+50
	Fine-adjusts the voice 2 pitch for resonance
	Voice2: Resonance		–100...+100
h	Sets the intensity of resonance when Control Mode = Manual			☞
	High Damp [%]	0...100%
	Sets the damping amount of resonant sound in the high range			☞
	Voice2: Level			0...100
i	Sets the Voice2 output level
	Pan				L6...R6
	Sets the Voice2 stereo image