The “Src” parameter sets the modulation source that resets the LFO. For example, you can assign Gate as a mod- ulation source so that the sweep always starts from the specified point.

“L LFO Phase” and “R LFO Phase” set the phase obtained when the left and right LFOs are reset. In this way, you can create changes in pitch sweep for the left and right chan- nels individually.

The effect is off when a value of the modulation source speci- fied in the “Src” parameter is 63 or smaller, and the effect is on when the value is 64 or higher. The LFO is triggered and reset to the “L LFO Phase” and “R LFO Phase” settings when the value changes from 63 or smaller to 64 or higher.

047: Dynam.Delay

(Stereo Dynamic Delay)

This stereo delay controls the level of delay according to the input signal level. You can use this as a ducking delay that applies delay to the sound only when you play keys at a high velocity or only when the volume level is low.

Stereo In - Stereo Out

 

 

 

 

Left

 

 

 

Wet / Dry

 

 

 

 

 

 

High Damp Low Damp

 

 

 

Delay

 

 

 

 

 

Feedback

Spread

 

 

 

High Damp Low Damp

 

 

 

Delay

 

 

 

Right

FB

 

Out

Wet / Dry

 

 

+

Envelope

Attack, Release

Control Target

 

 

Threshold

 

 

 

Control Target

None, Out, FB

a

Selects from no control, output, and feedback

 

 

Polarity

+, –

 

 

Reverses level control

 

 

 

 

Threshold

0...100

b

Sets the level to which the effect is applied

 

 

Offset

0...100

 

 

Sets the offset of level control

 

 

 

c

Attack

1...100

Sets the attack time of level control

 

 

 

 

d

Release

1...100

Sets the release time of level control

 

 

 

 

e

L Delay Time [msec]

0.0...680.0msec

Sets the delay time for the left channel

 

 

 

 

 

 

f

R Delay Time [msec]

0.0...680.0msec

Sets the delay time for the right channel

 

 

 

 

 

 

g

Feedback

–100...+100

Sets the feedback amount

 

 

 

 

 

 

 

Effects

205

 

ER/Delay

 

 

 

 

 

High Damp [%]

0...100%

 

Sets the damping amount in the high range

Fx:043

h

 

Low Damp [%]

 

0...100%

 

Sets the damping amount in the low range

 

Fx:043

 

 

 

 

 

 

 

i

Spread

 

–100...+100

Sets the width of the stereo image of the effect sound

Fx:043

 

 

 

 

 

 

 

 

Wet/Dry

Dry, 1:99...99:1, Wet

 

Table , “Sets the balance between the effect and dry sounds,” on page 175

 

 

 

 

 

 

 

 

 

 

 

 

 

 

j

Src

 

Off...Tempo

Table , “Selects the modulation source of the effect balance,” on page 175

 

 

 

 

 

 

 

 

 

Amt

 

–100...+100

 

Table , “Sets the modulation amount of the effect bal-

 

 

ance,” on page 175

 

 

 

 

 

 

 

 

 

a: Control Target

This parameter selects no level control, delay output con- trol (effect balance), or feedback amount control.

a:Polarity, b: Threshold, b: Offset, c: Attack, d: Release The “Offset” parameter specifies the value for the “Con- trol Target” parameter (that is set to None), expressed as the ratio relative to the parameter value (the “Wet/Dry” value with “Control Target”=Out, or the “Feedback” value with “Control Target”=FB).

When “Polarity” is positive, the “Control Target” value is obtained by multiplying the parameter value by the “Off- set” value (if the input level is below the threshold), or equals the parameter value if the input level exceeds the threshold.

When “Polarity” is negative, Control Target value equals the parameter value if the input level is below the thresh- old, or is obtained by multiplying the parameter value by the “Offset” value if the level exceeds the threshold.

The “Attack” and “Release” parameters specify attack time and release time of delay level control.

Level

Dynamic Delay

 

Dry

Threshold

 

Envelope

Release

Attack

 

Wet

(Ducking Delay)

Control Target=Out

 

Polarity= (–)

 

 

Delay Time

Wet

 

Control Target=Out

 

Polarity= (+)

 

 

Time

Page 207
Image 207
Korg KORG Pa50 user manual 205, Dynam.Delay, Stereo Dynamic Delay, Control Target