Korg KORG Pa50 user manual 080 OD/HG-ChoFl, Overdrive/Hi.Gain Chorus/Flanger

220Effects

Mono – Mono Chain

	[O] Output Level	0...50
	Sets the overdrive output level	☞ Fx:006,
b	Src		Off...Tempo
	Selects the modulation source for the overdrive output level
	Amt		–50...+50
	Sets the modulation amount of the overdrive output level
	[O] Low Cutoff [Hz]		20...1.00kHz
c	Sets the center frequency for Low EQ (shelving type)
	Gain [dB]			–18...+18dB
	Table , “Sets the gain of Low EQ,” on page 176
	[O] Mid1 Cutoff [Hz]	300...10.00kHz
	Sets the center frequency for Mid/High EQ 1 (peaking type)
d	Q		0.5...10.0
	Sets the band width of Mid/High EQ 1				☞ Fx:006
	Gain [dB]			–18...+18dB
	Sets the gain of Mid/High EQ 1
	[O] Mid2 Cutoff [Hz]	500...20.00kHz
	Sets the center frequency for Mid/High EQ 2 (peaking type)
e	Q		0.5...10.0
	Sets the band width of Mid/High EQ 2				☞ Fx:006
	Gain [dB]			–18...+18dB
	Sets the gain of Mid/High EQ 2
f	[A] Amplifier Type		SS, EL84, 6L6
	Selects the type of guitar amplifier
g	Routing	OD→ AMP, AMP→ OD
	Switches the order of the overdrive and amp simulation connection
	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
h	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt			–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

080: OD/HG-ChoFl

(Overdrive/Hi.Gain – Chorus/Flanger)

This effect combines a mono-type overdrive/high-gain dis- tortion and a chorus/flanger. You can change the order of the effect connection.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left			Wet / Dry
		Routing
	Overdrive / Hi-Gain
		Chorus/Flanger
	3 Band PEQ
+	Driver	Chorus/Flanger	Normal
	Output Level	+
			Output Mode
		–	Wet Invert
	Mode: Overdrive / Hi-Gain	Feedback
	Drive	Cho/Flng Wet / Dry
Right			Wet / Dry
		LFO: Tri / Sine

	[O] Drive Mode	Overdrive, Hi-Gain
a	Switches between overdrive and high-gain distortion
	Drive		1...100
	Sets the degree of distortion		☞ Fx:006

	[O] Output Level		0...50
	Sets the overdrive output level		☞ Fx:006,
b	Src			Off...Tempo
	Selects the modulation source for the overdrive output level
	Amt			–50...+50
	Sets the modulation amount of the overdrive output level
	[O] Low Cutoff [Hz]			20...1.00kHz
c	Sets the center frequency for Low EQ (shelving type)
	Gain [dB]				–18...+18dB
	Table , “Sets the gain of Low EQ,” on page 176
	[O] Mid1 Cutoff [Hz]		300...10.00kHz
	Sets the center frequency for Mid/High EQ 1 (peaking type)
d	Q			0.5...10.0
	Sets the band width of Mid/High EQ 1					☞ Fx:006
	Gain [dB]				–18...+18dB
	Sets the gain of Mid/High EQ 1
	[O] Mid2 Cutoff [Hz]		500...20.00kHz
	Sets the center frequency for Mid/High EQ 2 (peaking type)
e	Q			0.5...10.0
	Sets the band width of Mid/High EQ 2					☞ Fx:006
	Gain [dB]				–18...+18dB
	Sets the gain of Mid/High EQ 2
	[F] LFO Frequency [Hz]			0.02...20.00Hz
f	Sets the LFO speed
	LFO Waveform			Triangle, Sine
	Selects LFO Waveform
	[F] Delay Time [msec]			0.0...50.0msec
	Sets the delay time
g	Depth			0...100
	Sets the depth of LFO modulation
	Feedback				–100...+100
	Sets the feedback amount					☞ Fx:020
	[F] Cho/Flng Wet/Dry	–Wet...–2:98, Dry, 2:98...Wet
h	Sets the effect balance of the chorus/flanger		☞ Fx:010, 020
	Output Mode		Normal, Wet Invert
	Selects the output mode for the chorus/flanger			☞ Fx:067
	Routing	OD →	FLNG, FLNG → OD

iSwitches the order of the overdrive and chorus/flanger connection

☞Fx:067

	Wet/Dry	Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
j	Src		Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt		–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175